PERFECTPASS StarGazer Скачать руководство пользователя | Manualshive

Страница: 38 / 38

background image

LIMITED WARRANTY

During the first 12 months from date of original retail purchase, any PerfectPass component that fails
due to defects in materials or workmanship will be repaired or replaced at the option of PerfectPass
at no charge.

All warranty claims must be authorized in advance and a Return Authorization (R/A #) issued. All
packages, correspondence, documents and packing slips must reference this R/A #.

Warranty excludes components damaged my improper installation or improper use of boat. Servo
Motors are water resistant, but not water proof. Servo motors may become damaged if excess water
is run in a boats bilge and this may void warranty. Ensure your boat is properly “bilged” prior to
operating.

Warranty Service:

1.

If your PerfectPass was factory installed, any warranty issues should be directed to your
authorized dealer. PerfectPass encourages all customers to contact us prior to visiting your
dealer for “technical support” as many issues may be easily handled direct with customer.

2.

If your PerfectPass was purchased and installed by a dealer you may contact your dealer
direct or initiate a warranty claim with PerfectPass.

3.

If your PerfectPass was purchased directly from the Company, contact us at the number
below.

Warranty Service / Technical Support

PerfectPass Control Systems Inc.

14 Trider Crescent

Dartmouth, Nova Scotia

CANADA B3B 1R6

(902) 468-2150

(Hours: Monday to Friday 8:00 am – 4:00 pm EST)

«
...
36
37
38

Содержание StarGazer







































Отзывы:

Нет отзывов

Похожие инструкции для StarGazer

Бренд: Hammond Страницы: 8

Бренд: Audi Страницы: 9

Бренд: Belkin Страницы: 4

Бренд: B-Speech Страницы: 24

Бренд: Mercedes-Benz Страницы: 373

Бренд: Safe Fleet Страницы: 11

Бренд: Camec Страницы: 19

Ride-Rite Air Helper Springs 2173

Бренд: Firestone Страницы: 4

Бренд: Veigel Страницы: 24

Бренд: Cellular Line Страницы: 25

Бренд: Gear4music Страницы: 32

Бренд: VER-MAC Страницы: 64

Бренд: KEKO Страницы: 3

Бренд: Movon Страницы: 43

Бренд: Draw tite Страницы: 4

Бренд: Ranger design Страницы: 22

Бренд: Magneti Marelli Страницы: 3

Бренд: Curt Group Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды