manualshive.com logo in svg

PERFECTPASS StarGazer, Руководство пользователя

Поделиться
Скачать
PERFECTPASS StarGazer Скачать руководство пользователя страница 13

11 

 

 

If the times are not in tolerance or close to actuals then the RPM Baseline values will require 
adjustment.  The easiest way to do this in Jump mode is to go to Quick Recalibrate by pressing the 

DOWN

 key with the   highlighted.  This will bring you to the Calibration screen as seen below. 

 
 
 
 
 
 
 
 
 
 
 
 
Press the 

UP

 key on the Quick Calibrate message to recalibrate the baseline based on the times 

recorded from the last pass.  In this example it is suggesting your RPM Baseline should be increased 
by 135 rpm.  When you perform a Quick Calibrate the suggested adjust of 135 will be added to the 
baseline and saved in memory.  The system will also calibrate the digital speedometer if the times 
are with in the “OK” tolerance.   
 
Now engage system and time boat again.  If the times are still not close enough, repeat above steps 
until accurate.  If you wish to set up RPM Baseline values for other speeds (i.e. 31.7 mph), change the 
SETPOINT and repeat the above steps. 
 
 

JUMP DRIVING 

 
WARNING 

– Using the Jump mode with Jump Switch is for experienced drivers and skiers only.  

Please read carefully prior to operating.  The pull is very aggressive and designed for tournament 
water skiers only. You MUST have integrated timing and a proper jump course for system to operate 
properly.

 

 
Assuming the RPM Baseline values have been accurately set, you are now ready to tow skiers. 
 
First enter your Jump Letter or enter a “New Jumper” as explained above.  The Jump Letter can be 
changed by pressing the 

UP

 or 

DOWN

 keys with the Jump Letter highlighted on the screen. 

 
The key to a good pull and good times is to get the correct Jump Letter.  If the pull to the ramp is 
solid and the first segment time is good, you know the Jump Letter is OK.  If the time on the 1

st

 

segment was slow, you will require a higher letter on the next pass and vice versa. (Once engaged, 
push handle to full open position to allow PerfectPass room to throttle up when pulling long distance 
jumpers). 
 
If the first segment time was good, but the 2

nd

 was slow, raise the S2%. 

 

1. Quick Calibrate 

4. Menu Arrow 

2. SETPOINT 

Tachometer 

 

Course Time 

 

RPM Adjust 

3. Baseline 

 

Содержание StarGazer







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды