2. Press the
Menu button
, and then rotate the
Tuning knob
until the display shows
“System”.
3. Press the
Tuning knob
; rotate the
Tuning knob
until the display shows “Loudness”.
4. Rotate the
Tuning knob
to select between “Loudness On” or “Loudness Off”. Press
the
Tuning knob
to confirm the setting and return to normal display.
TONE
The
Tone
function enables the user to adjust the lower and higher sound frequencies.
1. Press the
On/Off button
to turn on the radio.
2. Press the
Volume knob
, the display shows “BASS 0”.
3. Rotate the
Volume knob
to set the desire Bass level.
4. Press the
Volume knob
to confirm, the display shows “TREBLE 0”.
5. Rotate the
Volume knob
to set the desire Treble level.
6. Press the
Volume knob
to confirm and return to normal display.
METAL TELESCOPIC ANTENNA
You can use this as an alternative antenna for your radio in areas or locations where the
radio signal (FM/DAB/DAB+) is weak to very weak.
ATTENTION: The standard antenna on the radio is flexible. The metal antenna
is not flexible or bendable and should be used with care. Breaking or bending
antennas is not covered by warranty.
Installing: Carefully screw off the standard flexible antenna. First carefully loosen the
antenna with an open-end-wrench key (size 14) – turn counter clockwise. Carefully
screw on the metal telescopic antenna and softly tighten it with an open-end-wrench key
(size 14) – turn clockwise.
ATTENTION: do not use too much force when fixing the antennas as this can
damage the screw threat of the antennas or make it break off
LANGUAGES
The menu of the radio can be configured to various languages.
1. Press the
On/Off button
to turn on the radio.
2. Press the
Menu button
, and then rotate the
Tuning knob
until the display shows
“System”.
3. Press the
Tuning knob
; rotate the
Tuning knob
until the display shows “Language”.
4. Press the
Tuning knob
to enter the language adjustment menu.
5. Rotate the
Tuning knob
until the desired language appears on the display (default
is English).
6. Press the
Tuning knob
to confirm your choice. The display menu will change to the
chosen language.
SOFTWARE VERSION
The software display cannot be altered and is just for your reference. You can only view
the software version in DAB and FM mode.
1. Press the
On/Off button
to switch on the radio.
2. Press the
Source button
to select FM or DAB mode.
3. Press the
Menu button
until the display shows “Full Scan”, and then rotate
the
Tuning knob
until the display shows “System”.
4. Press the
Tuning knob
; rotate the
Tuning knob
until the display shows
“SW version”.
5. Press the
Tuning knob
to view the software version.
6. Press the
Tuning knob
to back to last menu and press menu to return to
the normal radio display.
Note: USB socket inside battery compartment is for upgrading the software of the device
if needed.
SYSTEM RESET
If the radio fails to operate correctly, or some digits on the display are missing or
incomplete, carry out the following procedure.
1. Press the
On/Off button
to switch on the radio.
2. Press the
Menu button
,
3. Rotate the
Tuning knob
until the display shows “System”. Press the
Tuning knob
.
4. Rotate the
Tuning knob
until the display shows “Factory reset”. Press the
Tuning knob
.
5. Rotate the
Tuning knob
to select between “Yes” or “No”. Select “Yes” if you wish
to reset the radio, otherwise, select “No”.
6. Press the
Tuning knob
to cause the factory reset.
7. A full reset will be performed. All presets and the station list will be erased.
All settings will be set to the default values. The display will show “WELCOME
TO DIGITAL RADIO” for a few seconds, and then the radio will automatically
perform an auto scan of the Band III DAB channels and the FM band, the display
will show “Scanning” at DAB and “Auto” at FM.
In case of malfunction due to electrostatic discharge; reset the product as above to
resume normal operation. If you are not able to perform the reset operation as above,
remove and reconnect all batteries and the power supply.
G B
GB
13
14
