3
RSS260 AS
Operating instructions
Safety sensor
EN
Electrical data – AS-Interface
AS-i supply voltage:
18.0 ... 31.6 VDC, protection
against polarity reversal
AS-i power consumption:
≤ 100 mA
AS-i device insulation:
internal short-circuit proof
AS-i specification:
- Version:
V 3.0
- Profile:
S-0.B.F.E
AS-i inputs:
- Channel 1:
Data bits DI 0/DI 1 = dynamic code transmission
- Channel 2:
Data bits DI 2/DI 3 = dynamic code transmission
Databits condition static 0 or dynamic code transmission
AS-i Outputs:
- DO 0 ... DO 3:
no Function
AS-i parameter bits:
- P0:
Actuator present
- P1:
Hysteresis signal (FID)g
- P2:
Tamper protection time active (FID)
- P3:
Device error (FID)
Actuator detection (AD):
- P0 … P3:
Actuator number 0, 01 - 15
Parameter request:
default value parameter request "1111" (0xF)
AS-i Input module address:
0
- preset to address 0, can be changed through
AS-interface bus master or hand-held programming device
LED switching conditions display:
Green/red LED (AS-i Duo LED):
supply voltage /
communication error /
slave address = 0 /
periphery error detected /
tamper protection time active
Yellow LED:
device condition (enabling status) /
hysteresis signal / device error
For use in NFPA 79 Applications.
Only for use in Pollution Degree 2 Environment.
Adapters providing field wiring means are available from
the manufacturer. Refer to manufacurers information
This device complies with part 15 of the FCC Rules and
contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s
licence-exempt RSS(s):
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
This device complies with the Nerve Stimulation Exposure Limits
(ISED SPR-002) for operations with a minimum distance of
100 mm. Changes or modifications not expressly approved by
K.A. Schmersal GmbH & Co. KG could void the user's authority
to operate the equipment.
L’émetteur/récepteur exempt de licence contenu dans le présent
appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage.
(2) L’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le
fonctionnement.
Cet appareil est conforme aux limites d'exposition relatives à la
stimulation des nerfs (ISED CNR-102) pour les opérations avec
une distance minimale de 100 mm.
Changements ou modifications non expressément approuvés
par K.A.Schmersal GmbH & Co. KG pourrait annuler le droit de
l'utilisateur à utiliser l'équipement.
2.5 Safety classification
Standards:
EN ISO 13849-1, IEC 61508
PL:
up to e
Control Category:
4
PFH:
≤ 3.93 x 10
-10
/ h
PFD:
≤ 6.89 x 10
-5
SIL:
suitable for SIL 3 applications
Mission time:
20 years
3. Mounting
3.1 General mounting instructions
During fitting, the requirements of EN ISO 14119
must be observed.
The mounting holes provide for a variable mounting by means of M4
screws (max. tightening torque 0.8 Nm).
The component can be mounted in any position. The minimum bend
radius of the LST-type cable is 25 mm.
The active areas of the sensor and the actuator have to face each
other. The safety sensor must only be used within the assured
switching distances ≤ s
ao
and ≥ s
ar
.
The actuator must be permanently fitted to the safety
guards and protected against displacement by suitable
measures (tamperproof screws, gluing, drilling of the screw
heads).
To avoid any interference inherent to this kind of system and any
reduction of the switching distances, please observe the following
guidelines:
• The presence of metal chips in the vicinity of the sensor is liable to
modify the switching distance.
• Keep away from metal chips.
Minimum distance between two safety sensors as well as other
systems with same frequency (125 kHz):
50
109
90
100