manualshive.com logo in svg

Pepperl+Fuchs HiD2030, Руководство пользователя

Поделиться
Скачать
Pepperl+Fuchs HiD2030 Скачать руководство пользователя страница 15

Functional Safety HiD2030(SK)

Mounting and Installation

20

21

-0

9

15

4

Mounting and Installation

Mounting and Installing the Device

1.

Observe the safety instructions in the instruction manual.

2.

Observe the information in the manual.

3.

Observe the requirements for the safety loop.

4.

Connect the device only to devices that are suitable for this safety application.

5.

Check the safety function to ensure the expected output behavior.

4.1

Configuration

Configuring the Device

The device is configured via DIP switches. The DIP switches for setting the safety functions 

are on the side of the device.

1.

De-energize the device before configuring the device.

2.

Remove the device.

3.

Configure the device for the required safety function via the DIP switches, see chapter 3.3.

4.

Secure the DIP switches to prevent unintentional adjustments.

5.

Mount the device.

6.

Connect the device again.

Note

See corresponding datasheets for further information.

Содержание HiD2030























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды