manualshive.com logo in svg

Pepperl+Fuchs HiC2883, Руководство пользователя

Поделиться
Скачать
Pepperl+Fuchs HiC2883 Скачать руководство пользователя страница 14

20

17-

06

14

Functional Safety HiC2883

Mounting and Installation

4

Mounting and Installation

Installing the device
1. Observe the safety instructions in the instruction manual.
2. Observe the information in the manual.
3. Observe the requirements for the safety loop.
4. Connect the device only to devices that are suitable for this safety application.
5. Check the safety function to ensure the expected output behavior.

4.1

Configuration

Configuring the Device
The device is configured via DIP switches. The DIP switches for setting the safety 

functions are on the side of the device.
1. De-energize the device before configuring the device.
2. Remove the device.
3. Configure the device via the DIP switches.
4. Secure the DIP switches to prevent unintentional adjustments.
5. Mount the device.
6. Connect the device again.

Note!

The device configuration via DIP switches is not safety relevant.

Note!

See corresponding datasheets for further information.

Functional Safety HiC2883

Содержание HiC2883





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды