G-INSB-PROV (REV 12/2012)
4
Figure 3 Shows the main dimensions and part numbers of the ready to use filter kits with ProValve.
When using the complete filter and valve assembly , you will not need the adapter (item D in
figure 2
) . Make sure
however to use the 2 special 60.5mm fittings (on position F) included with the valve.
It is recommended to include manual valves in your installation enabling closing and bypass of the filter as illustrated in
figure 4
. In this illustration B is the output from the pump, C is the pool return. For winterizing, make sure to evacuate
all water from the ProValve.
It is possible to rotate in 90° increments the pump (B) and waste (A) connection on the valve if required in a specific
installation environment. This can be achieved after disassembling the 4 steel tie-rods . Rotate the ports with caution.
See
figure 5
.
Assembly of the ProValve can also be done away from the filter when preferred in a specific installation (
figure 6
). In
any case it is recommended to provide adequate support to the pipes into the valve and filter to provide sufficient
support for the valve.
PILOT
VALVE
INSTALLATION
The ProValve is actuated by air pressure. When activating the 230V pilot Valve included with the ProValve , this pilot
valve allows for the main cylinder in the valve to move down from filter to backwash position. The pilot valve is con
-
nected to your IntelliPool system (see IntelliPool manual for details) or any other backwash controller.
Figure 7
shows details of the connections onto the pilot valve. All air connections onto the pilot valve are threaded
in R1/8 BSP.
Use the supplied 6mm fittings and tubing to connect to your compressor from port ‘A’.
Mount one of the silencers on port ‘B’ (the second one can be mounted on the outlet on the side of the ProValve main
cylinder).
Port ‘C’ leads into the ProValve.
The Pilot Valve has a manual override that can be activated by using the pushbutton on position ‘D’.
The valve ctan be mounted on to the filter as shown in
figure 2
but it is preferred to mount it remotely from the filter
as illustrated in
figure 8
.
TECHNICAL SPECIFICATION
Material: glass reinforced >ABS<
Air pressure for Pilot Valve: 1.5 to max 3.5 bar (a basic compressor with 3l air tank is sufficient)
Pilot Valve operating at 230V AC , power consumption on activation: 8W
Max Valve Service pressure: 6 bar
Temperature range: 5 to 40°C
Port size: 2 ¾” BSP on unions, supplied with 63mm fittings
Head loss through the valve:
figure 9
Main Valve dimensions:
figure 10 and 11
Spare parts list available on
http://www.pentairpooleurope.com
/site/poolpros/en/spareparts/index.htm
A
B
C
D
E
(mm)
(mm)
(mm)
(mm)
(mm)
F-24S8-PRO
955
400
949
438
211
F-30S8-PRO
1095
610
1101
498
271
F-36S8-PRO
1200
610
1253
565
338
English
Содержание ProValve
