background image

1900 Series Horizontal Splitcase Pumps
Instruction and Repair Manual

17

11/12/18

TROUBLESHOOTING:

PUMP:

Your Fairbanks Nijhuis™ pump has been engineered and carefully selected for your application. It should provide years of 
trouble-free service. However, any piece of machinery is subject to wear and occasional malfunction.

To help you quickly isolate and rectify any malfunction, the following troubleshooting guide has been prepared.

Frequent use of the chart to determine the cause of minor operating problems may prevent a major problem or possible 
breakdown of your pump.

TROUBLE

PROBABLE CAUSE

REMEDY

1. Pump fails to prime or loses its

    prime.

a. Air leaks in suction lines.

a. Clean and tighten all suction 

prime connections; relocate 

suction inlet in liquid source.

b. Suction strainer is clogged.

b. Remove dirt, leaves, or other 

material from the strainer.

c.  Suction lift is too high.

c.  Re-evaluate pump requirements 

and correct suction conditions.

d. Defective priming valve.

d.  Replace valve.

e. Defective packing or seal.

e.  Replace packing or seal.

2. No discharge from pump.

a. Pump is not properly primed.

a.  Reprime the pump; refer to priming 

troubles and remedies.

b. Total head is too high.

b.  Re-evaluate head calculations; 

measure elevation differences 

between pump and liquid source 

and pump discharge point. Consult 

your local Fairbanks Nijhuis sales 

office.

c. Driver is not operating at rated 

speed.

c.  Check voltage of electric motor; 

check steam pressure of steam 

turbine; check engine RPM’s. 

Refer to appropriate maintenance 

manuals for possible troubles and 

corrective action.

d. Impeller or discharge line is 

clogged.

d.  Back flush pump to clear 

obstruction; disassemble pump 

and/or piping and remove 

obstruction.

e. Wrong direction of rotation.

e.  Check wiring against diagram 

motor nameplate and in controller; 

reverse any two power leads on a 

three phase motor, replace a single 

phase motor.

f.  Pump is vapor bound.

f.  Provide additional pressure on 

liquid being pumped by elevating 

liquid source or pressurizing the 

supply tank.

Содержание JUNG PUMPEN HIGHLOGO 1-910





































Отзывы: