Pentair FLECK 9100 SXT Скачать руководство пользователя страница 57

Страница: 57 / 108

Installer manual Fleck 9100 SXT - Programming

Ref. MKT-IM-004 / E - 06.10.2020

57 / 108

6.6.5

Volume since last regeneration (VU)

Info

Shows the volume used since the last regeneration (L).

1. Volume since last regeneration display (L or Gal depending on display

format programmed):

6.6.6

Reserve capacity (RC)

Info

Shows the remaining reserve volume until next regeneration (L).

1. Volume until next regeneration display (L or Gal depending on display

format programmed):

6.6.7

Software version (SV)

Info

Shows the version of the software used by the controller.

1. Software version display:

6.7

Resetting the controller

Mandatory

Once you have completed this operation, check all programming steps !

Info

There are two options to reset: partial and hard reset.

Partial reset will set all the parameters to default values, except volume remaining in
volumetric systems and days since last regeneration in time clock systems.

Hard reset will set all the parameters to default values.

6.7.1

Soft reset (SR)

1. Press and hold

and

for 25 seconds while in normal service mode

until

is displayed.

2. Reprogram all parameters in Master programming mode.

Содержание FLECK 9100 SXT













































































































Результаты поиска

Содержание FLECK 9100 SXT

Отзывы:

Похожие инструкции для FLECK 9100 SXT

Бренды по названию

Популярные бренды

Pentair FLECK 9100 SXT, Руководство по установке

Результаты поиска

Содержание FLECK 9100 SXT

Отзывы:

Похожие инструкции для FLECK 9100 SXT

Бренды по названию

Популярные бренды