Rev. G 6-27-03
5
P/N 190033
E. PREPARING DIATOMITE.
Your filter requires diatomaceous earth (D.E. or diatomite) for
proper filtration and operation. Your filter elements must be
precoated with this material in order to protect their surfaces
and provide the most efficient filtering action. Refer to Table 2
for the proper quantity to use with your filter. We recommend
the use of D.E. which is sold and labeled for use with
swimming pools and spas. These grades of D.E. typically
have a median particle size of 34 microns, which is ideal for
most applications.
1.
The FNS Plus Vertical Grid Series filters are listed with the appropriate amounts of diatomite to be used to precoat the filter
elements. A one (1) pound coffee can filled (level) with diatomite is equal to one half pound weight of diatomaceous earth.
Do not "pack" or compress diatomite into the coffee can.
2.
Mix the required amount of diatomite with sufficient water in a bucket to make a thin, milky mixture.
3.
Follow the instructions in Section D, COATING THE FILTER ELEMENTS to introduce the slurry of diatomite into the filter.
F. CLEANING THE FILTER MANUALLY.
1.
Turn the pump off, shut off any automatic controls to ensure that the system is not inadvertently started during servicing.
2.
Automatic skimmer should have Vari-Flo trimmer valve set to 100% skimmer. This will close off the main drain line. If there is
a separate skimmer line and main drain line plumbed to the pump, close the main drain valve.
3.
Open the filter High Flow™ manual air relief valve, and the waste drain valve or plug if your system has one.
4.
Remove the pump’s hair and lint strainer pot lid and clean the basket. Replace basket and secure lid. Follow the instructions
provided with your pump.
5.
Never attempt to assemble, disassemble or adjust the filter clamp while there is pressure in the filter.
Release the tank clamp
assembly and remove tank lid. Lift out the complete element for washing. Care should be taken not to lose or damage the
internal air relief, located on top of the manifold.
6.
Using your garden hose, thoroughly flush off all contaminated diatomite from the filter element surfaces.
NOTE
To clean individual grids, see Step 1, Section H, CLEANING FILTER ELEMENT.
7.
After coating the stand-pipe O-ring generously with a silicone base lubricant, replace the element assembly in the filter tank,
seating it firmly in place. Ensure the internal air bleed assembly is in place and free of diatomite or debris, see Section II,
CLEANING THE INTERNAL AIR BLEED TUBE.
8.
Ensure the O-ring is in position in the lower tank half. Place and press the filter lid over the lower tank half sandwiching the
O-ring in between.
9.
Replace tank top and carefully follow instructions in Section B, CLAMP INSTALLATION INSTRUCTIONS.
10.
Reset skimmer Vari-Flow Trimmer Valve or main drain line to pump; close waste drain valve or plug, and then follow the
procedure as outlined in Section D, COATING THE FILTER ELEMENTS.
G. CLEANING YOUR FILTER USING A SYSTEM WITH A SEPARATION TANK.
1.
Before working on any part of the circulating system, clamp, pump, filter, valve(s), etc., perform the following steps.
a.
Turn the entire pool/spa system off to ensure that the system is not inadvertently started during servicing.
b.
Open the High Flow™ manual air relief valve.
c.
Wait until all pressure is relieved.
Never attempt to assemble, disassemble or adjust the filter clamp while there is
pressure in the filter
.
2.
Turn skimmer to full skim position and close main drain line.
Table 2
Weight of
No. of 1 lb.
Filter Area (sq. ft.)
D.E.
Coffee Cans
24
2.4 lbs.
6
36
3.6 lbs.
8
48
4.8 lbs.
10
60
6.0 lbs.
12
