background image

SHURflo 316 Stainless Steel Rotary 

Close-Coupled External Gear Pumps

8

SHURflo Operating Instructions, Performance,  

Specifications and Parts Manual

Viton Models GMSV2A, GMSV4A, GMSV6C, GMSV2A3T, GMSV2A33T, 

GMSV4A5T, GMSV4A53T, GMSV6C7T and GMSV6C73T 

Teflon

®

 Models GMST2A, GMST4A, GMST6C, GMST2A3T, GMST2A33T, 

GMST4A5T, GMST4A53T, GMST6C7T and GMST6C73T 

Form L-4089 (2/17) 

Installation 

IMPORTANT: In any installations where 
property damage and/or personal  
injury can occur when the pump is  
not operating due to power outages,  
discharge line freezing, or any other 
reason, a back-up system(s) and/or 
warning system(s) should be used.
In order to safely use this product,  
familiarize yourself with this pump and 
also with the liquid (chemical, etc.)  
that is going to be pumped through  
the unit. This pump is not suitable for 
many liquids.
  1. Locate the pump as close to the  

liquid source as possible, making  
the suction line as short and direct 
as possible.

PIPING 
SUCTION
  2. Avoid excessive lengths or number 

of fittings and bends in the suction 
line.

  3. Attach suction line to suction inlet 

(See Figure 1 for proper rotation).

  4. It is recommended that same size 

pipe as pump ports be used or, in 
cases requiring lengthy piping, the 
next larger size pipe be used.

  5. If suction lift is greater than what is 

indicated in the performance chart, 
attach a foot valve below liquid 
level at end of suction line to ensure 
positive priming. Also note: If fluid 
specific gravity is greater than 1.4 or 
viscosity greater  
than 500 SSU, a foot valve is also 
recommended.

NOTE: If a foot valve (or check valve) is  
not used in the suction line, it may be  
necessary to refill the pump every time  
the unit is stopped and you wish to restart 
the pump. This depends on the length of 
time between starts and whether or not 
the gears are wet enough to close cavities 

to affect a prime.
  6. If solid contaminates are suspected 

in a liquid, place a filter in the  
suction line.

  7. Be certain all suction piping connec-

tions are airtight.

NOTE: Assure airtight pipe connections 
with the use of a pipe joint sealant.

DISCHARGE
  8. Attach discharge piping to the  

discharge outlet.

 

Support  pump and 

 piping during assembly 
and after installation. 

Failure to do so may cause piping to break, 
pump to fail, motor bearing failures, etc., all 
of which can result in property damage and/
or personal injury.

NOTE:  Should the pump need to be 
self-draining, the pump head should be 
mounted in the vertical position with 
the suction port facing down. When 
pumping high viscosity fluids, the 
vertical position can be used with the 
suction port facing up and the pump 
mounted under the source.  Increasing 
the suction pipe size and eliminating 
bends and elbows also assists in pump-
ing high viscosity fluids. Max. viscosity is 
500 SSU at 1725 RPM.
  9. If a shut-off valve or handgun is 

required in discharge line, provide  
a pressure relief valve for pump  
protection.

 

Shutting off  

 

 discharge without 
providing pressure 

relief can cause extreme overpressure which 
can result in pump and/or motor failure. Do 
not exceed 125 PSI pump or system pres-
sure.

 10. Operation under shut-off discharge 

conditions will overheat and  
damage pump. 

NOTE: Globe valve or other restrictive 
valves should not be used as shut-off 
mechanism as they are restrictive in 

nature and will seriously affect pump 
performance.
 11. After all piping and controls (not  

supplied with unit) have been 
installed, unit is ready for operation.

Operation

 

Do not run pump 
dry, as permanent 
damage to the pump 

gears, seal, and  
bearings will result. Suction pressure should 
never be greater than the discharge pres-
sure.

  1. All pumps must be primed before 

start-up and the seal chamber needs 

to be filled (See Figure 5). Never 
operate a pump unless it is secured 
to a solid foundation and all safety 
shields are installed.

    Upon start-up, maintain a minimum 

of 15 PSI (1 BAR) operating pressure 
on the pump. This will allow any 
remaining air to be driven from the 
seal chamber and will ensure liquid 
circulation to the mechanical seal.

  2. Gear pumps are built to very close 

tolerances and this tolerance must 
not be altered. The liquids must, 
therefore, be free of all abrasives. 
Sand, silt, wettable powders, etc. 
must be avoided. 

  3. When pumping a more viscous 

(beyond 500 SSU) liquid; a slower 
speed, a larger pipe size pump,  
and possibly a larger motor should 
be selected. 

Figure 5 - Prime Plug

Remove plug and fill seal chamber 

with fluid and reinstall plug

Содержание SHURflo Teflon GMST2A

















Отзывы: