background image

Item # E-03-487  6/10

Part # 5625-487-1

© 2010 Hydromatic

®

Ashland, Ohio.  All Rights Reserved.

– Your Authorized Local Distributor –

www.hydromatic.com

STANDARD LIMITED WARRANTY

 

 

 

 

HYDROMATIC

®

 warrants its products against defects in material and workmanship for a period of 12 months 

from the date of shipment from Hydromatic or 18 months from the manufacturing date, whichever occurs first - 
provided  that  such  products  are  used  compliance  with  the  requirements  of  the  Hydromatic  catalog  and         
technical  manuals  for  use  in  pumping  raw  sewage,  municipal  wastewater  or  similar,  abrasive  free         
non-corrosive liquids. 

During the warranty period and subject to the conditions set forth, Hydromatic, at its discretion, will repair or 
replace to the original user, the parts which prove defective in materials and workmanship. Hydromatic 
reserves the right to change or improve its products or any portions thereof without being obligated to provide 
such a change or improvement for prior sold and/or shipped units.

Start-up reports and electrical schematics

 may be required to support warranty claims. Warranty is 

effective only if Hydromatic authorized control panels are used. All seal fail and heat sensing devices must be 
hooked up, functional and monitored or this warranty will be void. Hydromatic will only cover the lower seal 
and labor thereof for all dual seal pumps. Under no circumstance will Hydromatic be responsible for the cost 
of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from 
the factory or an authorized Hydromatic service facility.

This limited warranty will not apply:

 (a) to defects or malfunctions resulting from failure to properly 

install, operate or maintain the unit in accordance with the printed instructions provided; (b) to failures resulting 
from abuse, accident or negligence; (c) to normal maintenance services and parts used in connection with such 
service; (d) to units which are not installed in accordance with applicable local codes, ordinances and good 
trade practices; (e) if the unit is moved from its original installation location; (f) if unit is used for purposes other 
than for what it is designed and manufactured; (g) to any unit which has been repaired or altered by anyone 
other than Hydromatic or an authorized Hydromatic service provider; (h) to any unit which has been repaired 
using non factory specified/OEM parts.

Warranty Exclusions:

 HYDROMATIC MAKES NO EXPRESS OR IMPLIED WARRANTIES WHICH EXTEND 

BEYOND THE DESCRIPTION ON THE FACE HEREOF. HYDROMATIC SPECIFICALLY DISCLAIMS THE IMPLIED 
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE.

Liability Limitation:

  IN  NO  EVENT  SHALL  HYDROMATIC  BE  LIABLE  OR  RESPONSIBLE  FOR         

CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES RESULTING FROM OR RELATED IN ANY MANNER 
TO ANY HYDROMATIC PRODUCT OR PARTS THEREOF. PERSONAL INJURY AND/OR PROPERTY DAMAGE 
MAY RESULT FROM IMPROPER INSTALLATION. HYDROMATIC DISCLAIMS ALL LIABILITY, INCLUDING   
LIABILITY UNDER THIS WARRANTY, FOR IMPROPER INSTALLATION. HYDROMATIC RECOMMENDS   
INSTALLATION BY PROFESSIONALS.

Some states do not permit some or all of the above warranty limitations or the exclusion or limitation of         
incidental  or  consequential  damages  and  therefore  such  limitations  may  not  apply  to  you.  No  warranties         
or representations at any time made by any representatives of Hydromatic shall vary or expand the         
provision hereof.

USA

740 East 9th Street, Ashland, Ohio 44805

Tel: 419-289-3042  Fax: 419-281-4087

CANADA

269 Trillium Drive, Kitchener, Ontario, Canada N2G 4W5

Tel: 519-896-2163  Fax: 519-896-6337

Содержание Hydromatic H3HX Series













Отзывы: