background image

1.

3.

4.

5.

7.

9.

WARNING! 

If the generator is installed indoors

DO NOT INSTALL 

INDOORS.
If the generator is installed outdoors

Never lift the generator using the engine 
or alternator lifting lugs.

Before using the generator, read 

and understand the engine manufacturer's 
Operation, Maintenance, and Parts manual. 
Also, read the safety precautions in this 
manual. These should always be followed to 
reduce the risk of personal injury and 
damage to equipment. 
Ensure installation meets all applicable 
safety, local and national electrical codes. 
Have installation performed by a qualified, 
licensed electrician and building contractor. 

exhaust fumes must be piped out of the 
building using leak-free, heat-resistant 
piping. Pipes and silencer should not be 
made of any flammable materials, nor should 
they be installed near any flammable 
materials. Generator exhaust fumes must be 
within legal limits, including all local codes 
and ordinances. 

, it 

must be weatherproofed and should be 
soundproofed. It should not be run outdoors 
without protection for both the generator and 
wiring conduit. 

 Connect lifting 

equipment to the frame of the generator. 
Before lifting the generator, ensure the lift 
rigging and supporting structure are in good 
condition, and are rated to lift such a load. 
The supporting floor/ground surface 

, and strong enough to safely hold 

the weight of the generator. If the 
floor/ground surface is not level, strong cross 
members should be placed under the full 
length of the generator frame at its low side. 
For trailer installation, the generator should 
be mounted on the center point of the trailer, 
over the wheels. 
All connections and conduits from the 
generator to the load must only be installed 
in compliance with all relevant local, state, 
and federal electrical codes and standards, 
and other regulations where applicable. 
Check with a qualified electrician.
The generator must be properly earth-
grounded by a qualified electrician in 
accordance with all relevant electrical codes 

2.

6.

8.

MUST 

BE LEVEL

IMPORTANT - All persons that will operate this equipment must read 
and become thoroughly competent with all operating procedures and 
safety precautions. Misuse of this equipment may result in death, 
personal injury or property damage.

OPERATING  PRECAUTIONS

and standards before operation. 
If an extension cord is used to provide power to a 
tool, make sure to use only UL

®

 approved cords 

having the correct gauge and length. 
Do not attempt to connect or disconnect load 
connections while standing in water, or on wet or 
soggy ground.
Do not touch electrically energized parts of the 
generator and interconnecting cables or conduc-
tors with any part of the body, or with any non-
insulated conductive object.
Connect the generator only to a load or electrical 
system that is compatible with the electrical 
characteristics and rated capacities of the genera-
tor.
Keep all electrical equipment clean and dry. 
Replace any wiring where the insulation is racked, 
cut, abraded or otherwise degraded. Replace 
terminals that are worn, discolored, or corroded. 
Keep terminals clean and tight. 

10.

11.

12.

13.

14.

(See page 9) 

15. Ensure that the generator is properly grounded 

before use

16.

17.

18.

. NEVER connect directly to a house or 

building electrical system without an electrician 
qualified to install the generator. Make sure that all 
connections comply with local codes.

 Failing to comply with this warning 

could result in a power backflow which could 
seriously injure or kill electrical or utility personnel.
If you are using this generator in highly conductive 
work areas such as around metal plating or a steel 
deck, be sure to use 

 Generator can reach temperatures as 

high as 150 degrees F (65 degrees C). Heed 
temperature warning labels on machine. Allow to 
cool before touching.

Become familiar with this manual and all safety 
precautions and warnings. Do not overload. 
Disconnect malfunctioning devices and do not 
exceed wattage capacity.

DANGER!

CAUTION!

Misuse can shorten the life of your generator. 

a ground fault circuit inter-

rupter (GFCI), available with some extension 

cords.

Copyright 2012 DTX International

6

Содержание HURRICANE PT10000E


























Отзывы: