PENSOTTI PCC 34 H Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 30

background image

Version 1

30

Water Test and Treatment

34. Test the heating system boiler water.

When purchased, every Pensotti condensing boiler is supplied with a Fernox Express

Water Treatment Kit. Within it is a water test kit, along with instructions. Following those instructions; test the water and if
necessary, treat as required. Keep a detailed history of the water quality test to assist in creating a schedule for future treatments.

Warning

Read and follow all safety precautions on the label of all water treatment chemicals.

Important

Failure to test and treat the boiler water on a regular basis may result in premature failure and will void the warranty.

35. Install and secure the front cover(s). Complete.

«
...
28
29
30

Содержание PCC 34 H































Отзывы:

Нет отзывов

Похожие инструкции для PCC 34 H

Бренд: RBI Страницы: 44

NINFA N LOW NOX 24 MCS

Бренд: Lamborghini Caloreclima Страницы: 144

Prestige Slol 250

Бренд: TriangleTube Страницы: 89

EXALT Combi 155

Бренд: IDEAL Страницы: 39

Бренд: Trianco Страницы: 18

Бренд: Kiturami Страницы: 45

Бренд: Ariston Страницы: 88

EnduroTI ETI-1000

Бренд: HTP Страницы: 67

Бренд: HTP Страницы: 83

Бренд: OERTLI Страницы: 4

Brava One HE 25 ErP

Бренд: Sime Страницы: 68

Бренд: STYLEBOILER Страницы: 24

Mexico Super CF445

Бренд: Ideal Boilers Страницы: 4

Бренд: Potterton Страницы: 20

Бренд: Baxi Potterton Страницы: 12

Бренд: gassero Страницы: 40

Бренд: Viessmann Страницы: 44

Direct Vent DVF-4 Rigid

Бренд: QHT Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды