PENSOTTI PCC 34 H Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 30

background image

Version 1

23

Combustion Chamber Cleaning Procedure

19. Repeat step 16

and brush the wetted heat exchanger to remove additional debris from the heat exchanger surface.

20. Again, using a garden hose with a trigger spray nozzle or similar device,

direct pressurized water in the space between the heat

exchanger tubes. Repeat steps 18 and 19 until the heat exchanger is thoroughly cleaned and the water running into the bucket remains
clear. For especially stubborn debris, a 50/50 mix of CLR and water may be used in place of just straight water. It is imperative that upon
completion, the heat exchanger be thoroughly rinsed with clean water to remove all CLR chemical remnants.

Repeat

Brush

Rinse

«
...
21
22
23
24
25
...
»

Содержание PCC 34 H































Отзывы:

Нет отзывов

Похожие инструкции для PCC 34 H

Бренд: Malvern Страницы: 30

aroSTOR VWL B 270/5

Бренд: Vaillant Страницы: 172

LOGIC SYSTEM S15IE

Бренд: Ideal Heating Страницы: 80

Бренд: Zip Страницы: 28

Бренд: Daikin Страницы: 12

HR EVO 200 SMART

Бренд: Ravelli Страницы: 357

Бренд: Daikin Страницы: 12

VOGUE MAX SYSTEM 32IE

Бренд: Ideal Heating Страницы: 80

Minimiser FF 30

Бренд: IDEAL Страницы: 4

GENUS HE 35 Plus

Бренд: Ariston Страницы: 68

Бренд: Immergas Страницы: 4

ECO COMPACT 200

Бренд: Pleion Страницы: 11

Prestige SOLO 299

Бренд: TriangleTube Страницы: 5

Бренд: Garland Страницы: 16

TURBO CONDENSING - 13

Бренд: Kiturami Страницы: 53

Бренд: Buderus Страницы: 52

Бренд: HTP Страницы: 112

Бренд: eta Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды