Pensa Labs D.I.Wire Pro Скачать руководство пользователя страница 28

Страница: 28 / 84

FIT TO
SCREEN

Resize the view of the

workspace to show the

entire active part.

ZOOM IN

ADD A
VERTEX

SELECT
VERTICES

ZOOM OUT

REMOVE A
VERTEX

CHANGE
STARTING
POINT

PAN

Zoom into desired details of

the workspace.

Add new bend points on

the active path

Click on line segments and

bend points to move them

around on the workspace.

Zoom out to view more of

the workspace.

Remove bend points from

the active path

Choose which end of the

path to start bending

Move around the viewable

area of the workspace by

clicking and dragging.

ADD A
PAUSE
POINT

Select a Bend Point where the

machine will pause before the

bending at that location

CTRL + U

CTRL + SHIFT + U

Undo previous action on the

Workspace

Redo previous action on the

Workspace

Zoom tools help you to navigate around

your workspace.

Select Tool allows you to click on line

segments and bend points and move them.

ZOOM

SELECT

UNDO
TOOL

Click on the Undo Tool to undo

changes made on the path

Undo changes made to the Path.

UNDO TOOL

Toolbar

04 | PATH MODE

The Zoom, Select and Undo tools allow for flexible navigation

of the workspace and control of the path.

Содержание D.I.Wire Pro





















































































Результаты поиска

Содержание D.I.Wire Pro

Отзывы:

Pensa Labs D.I.Wire Pro, Руководство пользователя, Страница: 28 / 84

Результаты поиска

Содержание D.I.Wire Pro

Отзывы: