Pensa Labs D.I.Wire Pro Скачать руководство пользователя страница 14

Страница: 14 / 84

POWER OFF

ADULT
SUPERVISION
REQUIRED

AVOID
LOOSE
CLOTHING

TIE
HAIR
BACK

TO STOP
MACHINE

REMOVE
JEWELRY

Power off your D.I.Wire when not in use

Loose jewelry, like necklaces and/or

braceletscan get caught in the moving

components. Remove all loose jewelry

items before operating the D.I.Wire.

Long sleeves, ties, sweaters, hoodies

and other loose clothing can get

caught in the moving components.

Do not wear loose clothing while

operating the DIWire

Long hair can get caught in between the

moving components and seriously hurt

you. Long hair must always be tied back

Press STOP or PAUSE in WireWare, or

Hit the Power Button

MOVING
PARTS

NEVER touch the Bend Pins or

Feed Wheels during bending. Allow

the D.I.Wire to finish bending before

reaching into the top plate.

STOP

Your safety and the safety of others is very important to us, so we have provided the

following safety section and other safety-related messages along the manual. Always

read and follow all safety messages.

NEVER TOUCH

MOVING PARTS!

AVOID
WATER

The D.I.Wire and its power supply are not

water proof, keep clear of water and other

liquids. Refer to the maintenance section

for cleaning instructions. Keep the power

adaptor away from water

Not a toy, the D.I.Wire is intended for use

only by or under supervision of adults

Bend Safety

02 | SETUP AND SAFETY

Orient the machine so the switch

is easily accessible

Tip: don’t put your coffee cup

on top of your D.I.Wire!

Содержание D.I.Wire Pro





















































































Результаты поиска

Содержание D.I.Wire Pro

Отзывы:

Pensa Labs D.I.Wire Pro, Руководство пользователя, Страница: 14 / 84

Результаты поиска

Содержание D.I.Wire Pro

Отзывы: