Penn A52 Series Скачать руководство пользователя страница 54

Страница: 54 / 56

A52x Series Electronic Refrigeration Controller with Adaptive Defrost Technical Bulletin

Rated for 24 A at temperatures up to 45°C (113°F). From 45C° to 60C° (113F° to 140F°), the Ampere rating decreases from 24 A to 15 A

at a rate of 0.6 A per 1°C. The A52x Controller is not rated for use in ambient conditions above 60°C (140°F).

Table 13: SPST High Speed Fan (HI_SPD) Relay Electrical Ratings

Agency and File

UL 60730

EN 60730

Applied AC Voltage at 50/

60 Hz

24 VAC

120 VAC

240 VAC

Horsepower

1/2 HP

Full Load Amperes

9.8 A

4.9 A

Locked Rotor Amperes

58.8 A

29.4 A

Resistive Amperes

10 A

Pilot Duty VA

125 VA at 24 to 240 VAC

Table 14: SPST Defrost Relay Electrical Ratings

Agency and File

UL 60730

EN 60730

Applied AC Voltage at 50/

60 Hz

24 VAC

120 VAC

240 VAC

Resistive Amperes

10 A

24 A

Pilot Duty VA

125 VA at 24 to 240 VAC

Table 15: (Part 1 of 2)A52x Refrigeration Controller with Adaptive Defrost

Product

A524/A525

Power Consumption

1.8 VA maximum

Supply Power

84 VAC to 260 VAC, 50/60 HZ, 10 VA maximum

Ambient Conditions

Operating:

-30C°–60C° (-22F°–140F°), 0 to 95% RH non-condensing



Shipping and Storage:

-40C°–85C° (-40F°–185F°), 0 to 95% RH non-condensing

Temperature Sensing

Range

-40C°–50C°(-40F° –122F°)

Input Signal (Sn1 and Sn2)

1,035 ohms at 25



C (77



F) for A99B PTC temperature sensors

10,000 ohms at 25



C (77



F) for TS-6340 NTC temperature sensors

Input Signal (UI4 and UI5)

0–10 VDC input for leak detector status or dry contact binary input with a switch wired between

terminals UI4 and UI5 and C.

HVBIN Signal

120 VAC or 240 VAC

Sensor Offset Range

±3ºC or ±5ºF

RS485 MODBUS

Maximum distance is 100 ft; 9.6K baud is the default but 19.2K is also supported.

External USB

Use a standard USB flash drive to extract HACCP data or update firmware revision for future

upgrades.

Enclosure

IP65 watertight, corrosion-resistant, high-impact thermoplastic

Dimensions (H x W x D)

196.8 mm (7.75 in.) x 190.5 mm (7.5 in.) x 82.6 cm (3.25 in.)

Weight

1.1 kg (2.4 lb)

Содержание A52 Series

























































Результаты поиска

Содержание A52 Series

Отзывы:

Похожие инструкции для A52 Series

Бренды по названию

Популярные бренды

Penn A52 Series, Технический бюллетень

Результаты поиска

Содержание A52 Series

Отзывы:

Похожие инструкции для A52 Series

Бренды по названию

Популярные бренды