manualshive.com logo in svg

PenBits PK017, Руководство по сборке

Поделиться
Скачать
PenBits PK017 Скачать руководство пользователя страница 65

Bachmann 'Peak': Final Assembly

Lubricate the teeth of all gears in the drive train using a suitable grease. Lubricate the
worm shaft bearings with a light oil.

Assuming  that  you  have  the  wheelsets  and
springs  already  fitted  in  to  the  Subframe,

rest  the  subframe  on  your narrow  wheeling
block.  Orientate  the  Drive  Unit  correctly  over
the  outer  and  centre axles.  Carefully  align  the
Bachmann  bearings  on  each  axle  and,  one  axle
at  a  time,  clip  the  drive  unit  into  place on  the
axles.

Note  that  the  photos  here  show  the  worm  drive  fitted;  you  might  wish  to  leave  it
off for now to do the further rolling test suggested below.

In  any  subsequent  dismantling  and  reassembly,  we  recommend  that  you  keep  the
wheelsets clipped in to the Drive Unit and remove them together from the Subframe

by unclipping the springs. Reassembly follows a similar procedure to that followed earlier in
the Bogie Assembly section, but with the wheelsets now clipped into the Drive Unit.

Check  clearances  around  the  drive  unit,
and for free-running of the gears.

Refit the Bolster to the Subframe, again checking clearances.

Repeat the above for the other bogie.

You  now  have  the  option  of  re-assembling  the  bogies  into  the  loco  and  doing  some
unpowered  testing  to  check for  free  running  of  the  gears.  Bear  in  mind  that  the

components  are  not  yet  run-in  in  their  current configuration:  any  slight  imperfections
might be eased out by a few minutes under power.

With the bogies once more out of the loco, separate the Subframes from the Bolsters.

Fit the worm shafts and their bearings, with a smear of grease on the worm itself and
some light oil in the bearings. Fit the Worm Bearing Retainer etches.

Undo the screws retaining the Pivot Frames to the Bolsters, and reassemble them with
a thread locker applied to the screws, to prevent them working loose in service.

Special thread locking compounds can be bought. Nail varnish, or paint, will also do the
job.

Refit the Bolsters on to the Subframes.

Clip the drive shafts - the ends with the rounded pins - into the sockets on the worm
shafts.

Bachmann 'Peak': Final Assembly

65/65

(c) PenBits Model Railways, All Rights Reserved

27/09/2021

Содержание PK017



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды