manualshive.com logo in svg

PenBits PK017, Руководство по сборке

Поделиться
Скачать
PenBits PK017 Скачать руководство пользователя страница 16

We  hold  the  0.9mm  wire  in  the  correct
alignment  with  the  bearing  as  shown  here.

C la mp the  wire  horizontally  in  the  'helping
hands'  at  a  distance  above  the  bench  that
allows  the  hand  vice,  holding  the bearing,  also
to  rest  on  the  bench.  Using  one  hand  to
steady  the  vice,  the  other  is  free  to  wield  the
soldering iron.  Snip  off  the  wire,  close  to  the
bearing, when done, and it's ready for the next
one.

Trim the wire and file it flush with the front edges of the ears and with the back of the
bearing. Clean off any solder which adheres to the outer faces of the ears. Ensure  the

holes in the ears remain clear of solder.

Taking  each  subframe  etch  in  turn,  check  that  the  carrier
assemblies  can  slide  freely in  their  respective  subframe  slots  (see

the  next  paragraph  for  a  solution  to  bearing  misalignment). File  away
any  burrs  from  the  outer  edges  of  the  carrier  tops. The  fit  along  the
line of the axle, i.e. of the subframe plate between the  bearing  flange
on  one  side  and  the  inner  facing  edges  of  the  carrier  on  the  other,
should  be  quite  loose to  accommodate  tilting  of  the  axle.  Check  that
all traces of the tag are removed from the edge of the bottom face of
the carrier, as otherwise it can bind with the lower edge of the subframe slot.

Although  the  aim  is  to  have  the  bearing
flange  parallel  with  the  front  face  of  the

carrier,  a  certain  amount  of  misalignment  can
be  tolerated.  If,  however,  you  find  that  the
subframe  side  is  'pinched'  between  the  two,
then  an  individual  carrier  assembly  can  be
corrected  by  clamping  the  back  of  the  top  of
the  carrier  against a  flat  working  surface.  The
soldering  iron  can  then  be  applied  to  the
bearing  to  melt  the  joint  between  bearing and
carrier and allow the back of the bearing to be
held  down  against  the  same  surface.  This
should set the correct alignment.

That  completes  the  bearing  carriers.  Clean  them  up to  remove  any  flux  and  grease
residues and put them, and the subframes, away in their respective containers.

Bearing Carrier Instructions for Co1 Bogies

16/65

(c) PenBits Model Railways, All Rights Reserved

27/09/2021

Содержание PK017



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды