manualshive.com logo in svg

PenBits PK017, Руководство по сборке

Поделиться
Скачать
PenBits PK017 Скачать руководство пользователя страница 15

best to leave cleaning up the tags until after the folding and soldering stages below.

Taking  each  carrier  in  turn,  clamp  it  firmly
into  a  vice  (a  hand-held  vice  is  ideal  for

t his) across  the  ends  of  the  bearing with  the
bottom  of  the  bearing  carrier  protruding.  File
away  any  remnants  of  the  tag  from  the  lower
edge of the carrier.

Working  against  a  hard,  flat  surface,  make
the  fold  to  form  the  bottom  flange  of  the

bearing carrier.

Then,  invert  the  carrier  in  the  vice  so  that
the  carrier  top  is  projecting.  Fold  in  the

ears  at  the  top  of  the carrier.  You  may  find
that  the  ear  catches  against  the  top  flange:
do  not  apply  brute  force,  but  adjust  Fold  2
and/or  the  direction  of  the  applied  force,  and
you will find that it folds easily. Folding against
a block, as shown, gives a good, tight fold.

Pass a piece of the 0.9mm nickel-silver wire through the hole
in  the  back  of  each  carrier  and  across  the  top,  parallel  to

the line of the axle.  With a small amount of flux,  solder  the  wire
in  place,  at  the  same  time  reinforcing  the  folds  and  butt  joints
around  the  top  of  the carrier.  Keep  the  bearing  clamped  in  the
vice  while  soldering;  this  will  act  as  a  heat  sink  and  prevent
melting of the joint between the bearing and carrier.

Bearing Carrier Instructions for Co1 Bogies

15/65

(c) PenBits Model Railways, All Rights Reserved

27/09/2021

Содержание PK017



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды