manualshive.com logo in svg

PenBits BACHMANN CLASS 24, Руководство по сборке

Поделиться
Скачать
PenBits BACHMANN CLASS 24 Скачать руководство пользователя страница 22

From  inside  the  subframes,  fit  each  ear
through  the  slots  in  the  centre  of  the

subframe  sides. The  base  of  the  ear  should
come  up  flush  to  the  inside  face  of  the
subframe  side,  handed  so  that  it  is  on the
same  side  of  the  slot  as  the  hole  in  the
subframe.  Make  sure  you  have  them  the  right
way  up;  the  top of  the  base  should  align  with
the  top  of  the  subframe,  and  the  hole  in  the  ear  should  be  towards  the  top. Solder  each
ear in place, applying flux to the base and solder to the large hole in the subframe, letting
i t flash  round  the  joint.  Ensure  that the  hole  in  the  ear,  for  the  primary  spring  beam,
remains clear.

Undertray and Secondary Spring Seats

Remove  the  undertray  plate  from  the  fret.
Make  the  folds  at  each  end  of  the  plate.

Check  the  fit  of  the plate  into  the  subframe,
noting  that  the  lugs  on  the  sides  of  the plate
engage  in  the  recesses  in  the  lower  edges  of
the subframe, and that the fit is reversible end
for end.

Remove  the  secondary  spring  seat  etch
from the fret and clean it up.

Make  the  folds  in  the  spring  seat  etch  and
fit  its  tabs  into  the  slots  in the  top  face  of

the  undertray.  Ensuring  that  the  seats  and
undertray  are  correctly  aligned,  solder  the  two
together.

Fit  the  undertray  into  the  subframe  and
solder up.

Bachmann Class 24/25 Subframes

22/51

(c) PenBits Model Railways, All Rights Reserved

27/09/2021

Содержание BACHMANN CLASS 24





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды