manualshive.com logo in svg

PenBits BACHMANN CLASS 24, Руководство по сборке

Поделиться
Скачать
PenBits BACHMANN CLASS 24 Скачать руководство пользователя страница 12

Remove the bearing carrier frames from the
main  etch.  DO  NOT  at  this  stage  separate

the bearing carriers from the frames.

The  individual  bearing  carriers
each 

have 

small 

half-etched

identification  marks.  You  can  use  these
in conjunction with corresponding marks
on  the  subframes  to ensure  that  each
carrier  is  always  mated  with  the  same
subframe slot.

Test  fit  the  bearings  in  the  large  central
holes  in  the  carriers.  The  body  of  the

bearing  (excluding  the flange)  should  pass
through  the  hole.  If  necessary,  gently  relieve
the  holes  with  a  round  needle  file,  working
evenly  around  the  edges,  until  the  bearings
pass through.

The folds in the bearing carrier frames are
best  made  in  bending  bars,  or  between

any  two  trued  and  parallel surfac es clamped
together.  Use  a  rigid  piece  of  flat  material  to
make  each  bend  simultaneously  along  its  whole
length.  This  will  help  minimise  any  unwanted
distortion in the fret. 

Note that Fold 3 is a jig fold, made along the tags at the base of the carriers.

Bearing Carrier Instructions for Four-wheel Bogies

12/51

(c) PenBits Model Railways, All Rights Reserved

27/09/2021

Содержание BACHMANN CLASS 24





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды