Peg-Perego Pliko P3 Modular e, Инструкция по эксплуатации

Страница: 25 / 92

- 25 -
opposite. The waist strap can be tightened as far
as the safety stop (Fig. b).
29• To adjust the height of the safety harness, it is
necessary to release the two buckles on the rear of
the backrest.
Pull the straps towards you (arrow a) until the
buckles are released, then slip them through the
slots in the backrest (arrow b). Pull the shoulder
straps through the fabric cover (arrow c) and push
them back through the most suitable slot (arrow
d), then reattach the two buckles behind the
backrest (arrow e). The buckles click when they are
correctly attached (fig f).
30• ADJUSTING THE FOOTREST: the footrest can be
adjusted to three positions. To lower the footrest,
pull the two side levers downwards and at the same
time lower it. To raise the footrest, push it upwards
until it clicks into position.
31• ADJUSTING THE BACKREST: the backrest can be
reclined in four positions. To lower the backrest,
raise the handle and at the same time lower the
backrest, locking it in the required position. To
raise it, push the backrest upwards.
32• FRONT BAR: the chassis is supplied with armrest
closure caps fitted. To fit the front bar they must
be removed. Keep the caps in a safe place in case
you decide to use the stroller without the front
bar. To remove the caps, press the button under
the armrest and at the same time extract the cap.
Repeat on both armrests (Fig.a).
To attach the front bar, insert the two ends of the
front bar until they click into position (Fig.b).
33• It is possible to open the front bar on one side to
facilitate the entry and exit of the child when he/
she is bigger. To open it, press the button under
the armrest and at the same time pull the front bar
outwards (Fig.a). To remove the front bar press the
two buttons under the armrests and at the same
time pull the front bar outwards (Fig.b).
34• REAR LEDGE: the rear ledge helps negotiate small
steps and can be used to transport a second child
(fig_a).
LOADING SEQUENCE: to use the Pliko P3 with two
children (fig_b), first apply the stroller brakes, then
place the smaller child in the seat and fasten the
safety harness (1). Grip the handles (2) and allow
the second child to get onto the ledge (3).
• Never leave the children unattended.
• Do not allow a child to get onto the rear ledge
when the stroller is empty.
35• CLOSING: before closing the Pliko P3, it is
necessary to detach the Navetta XL bassinet
unit or Primo Viaggio tri-fix es car seat. The
stroller can be folded with just one hand: pull first
one lever upwards and then the other, until they
release.
36• Grip the central handle and pull it upwards until
it closes (fig_a). Check the correct closure of the
chassis with the safety clip. When closed the
chassis is freestanding (fig_b).
37• TRANSPORT: The Pliko P3 can be easily transported
(with the front wheels adjusted for fixed direction)
by holding the central handle (fig_a). It can also be
carried with the side handle (fig_b).
38• REMOVABLE COVERS: to remove the stroller covers,
unfasten the cover buttons from the armrests as
shown with the arrows (fig_a). Unscrew the safety
harness (only from one side), holding a finger under
the nut (fig_b).
39• Detach the side cover button and unthread the
harness leg divider strap from under the seat (fig_a).
Unfasten the cover buttons from the seat and slide
the cover off to remove it from the footrest fasteners.
Pull the cover upwards to remove it (fig_b).
40• Changing BAG (included): Bag with baby changing
pad. Can be attached to the stroller (fig_a).
SERIAL NUMBERS
40• The following information can be found behind
the backrest of the Pliko P3: Product name,
production date and serial number (fig_b).
This information is required in the event of a
complaint.
ACCESSORIES
41• TRAVEL BAG: Practical bag for taking the stroller
on planes.
MOSQUITO NET: For attachment to the hood.
PARASOL: Practical matching parasol.
CLEANING AND MAINTENANCE
PRODUCT MAINTENANCE: protect from the
weather: water, rain, or snow; prolonged and
continuous exposure to bright sunlight may give
rise to colour changes of various different materials;
store this product in a dry place.
The maintenance
have to be regularly.
CLEANING THE CHASSIS: periodically clean all
plastic parts with a damp cloth. Do not use solvent
or similar cleaning products; keep all metal parts
dry to prevent rusting; keep moving parts clean
(adjustment mechanisms, locking mechanisms,
wheels, ...) and free of dust and sand and, if
necessary, lubricate with light machine oil.
CLEANING THE RAIN CANOPY: wash with a sponge
and soapy water; do not use detergents.
CLEANING FABRIC PARTS: brush fabric parts to
remove dust and wash by hand at a maximum
temperature of 30°C; do not wring; do not use
chlorine bleach, do not iron; do not dry clean; do
not apply solvent-based stain removers and do
not dry in a tumble dryer.
PEG-PÉREGO S.p.A.
Peg-Pérego S.p.A. is an ISO 9001
certified company. This certification is
a guarantee for customers and
consumers of the transparency and
trustworthiness of the company's
procedures and working methods. Peg Pérego can
make changes at any time to the models described
in this publication for technical or commercial
P3Modular&P3OnTrackModular-EU_FI25 25 11-02-2010 17:12:49