Peg-Perego DESMOSEDICI IGED1048, Инструкция по использованию и уходу

Страница: 9 / 40

For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• The toy must be used with caution, as it requires
substantial dexterity in order to avoid falls or
collisions which could cause injuries to the user or
third parties.
• Before starting, check that there are no people or
objects obstructing the vehicle’s path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
ATTENTION! The item is equipped with a brake
system which needs to be appropriately illustrated to
the child by an adult.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds.
• If the vehicle is overloaded on steep slopes, the
overload cut-out will immediately disconnect the
power. If this happens, REMOVE THE FOOT FROM
THE ACCELERATOR. The electrical brake will be
activated, slowing down the descent of the vehicle.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.
PROBLEMS?
RULES FOR SAFE DRIVING
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
ASSEMBLY
1 • Slip a plastic washer and one of the two widest
wheels onto the axle.
2 • Insert the axle all the way into the hole in the
reduction gear so that it protrudes from the
opposite part of the vehicle.
3 • Slip an iron washer and the last large wheel onto
the axle.
4 • Slip a plastic washer onto the axle and fasten the
wheels with an 11ø bolt.
NOTE: If the axle is too long, add another
plastic washer before fastening the bolt.
ATTENTION: There are 4 different-sized bolts in
the bag. It is possible to tell the bolts apart by
checking the different size of the central hole on
the bottom of them.
5 • Remove the axle from the fork; discard the
bushing (A).
6 • Insert the mudguard till it clicks as shown in the
figure.
7 • Place the two hub-caps on the last wheel (the
narrowest one of the three wheels in the
package).
8 • Position the wheel on the fork and insert pin
which you have previously taken out.
9 • Insert the bolt 9 ø in the special tool; lock the
wheel as shown in the figure.
10 • Insert the fork.
11 • Position the windshield on the grill.
12 • Position the dashboard on the lower pins (shown
by the arrow). Press on the sides and on the
upper side of the dashboard to fit it properly.
13 • Insert the grill on the fork.
14 • Insert the handle till it clicks.
15 • Apply the glass on the front light till it clicks.
16 • Apply the indicators on the grill first inserting
the back notch, then pressing. A: Right turn
indicator, (you recognise it from the letter D
printed on the inner part).
17 • Insert the roll-bar tabs into the body holes and
turn the roll-bar downwards.
18 • Screw the roll-bar.
19 • Insert the two exhaust pipes into the openings
on the back of the vehicle. Press to click into
place.
20 • Rotate the red catch behind the saddle until
bringing it to the position shown on figure A. Lift
up the saddle.
21 • Connect the plugs. When you have finished,
remember to close and fix down the saddle. The
toy vehicle is now ready for use.
INSERTING BATTERIES
To allow the lights and electronic sounds to work, do
as follows.
22 • Undo the screw of the cover of the battery
chamber on the dashboard. Remove the battery
chamber.
23 • Take out the battery holder.
24 • Insert the two 1.5V AA batteries (not provided).
Reposition the battery holder inside the
dashboard and close the cover, screwing the
screw back in.
FEATURES AND USE OF THE VEHICLE
25 • A: button for intermittent lights
B: button for horn
C: ignition key; when the key is turned to the
right, you will hear the sound of the “engine’s
roar” and it will be possible to work the
intermittent lights and the horn. Note: turn the
key to the left as soon as you have finished using
the various functions in order to preserve the
life of the batteries.
26 • PEDAL: Accelerator only, brake is automatic.
REPLACING BULBS (2.5 Volt)
27 • Undo the screw of the fused indicator light. Take
away the glass covering it.
28 • Replace the fused bulb.
29 • Put the glass back in place in front of the
indicator and screw the screw back in.
ASSEMBLY INSTRUCTIONS
REPLACING THE BATTERY
PLEASE NOTE: THE PICTURES OF THE BATTERIES
ARE FOR ILLUSTRATIVE PURPOSES ONLY. YOUR
BATTERY MAY BE DIFFERENT FROM THE MODEL
SHOWN. THIS DOES NOT AFFECT THE
REPLACEMENT AND CHARGING PROCEDURES
DESCRIBED.
30 • Rotate the red catch behind the saddle until
bringing it to the position shown on figure 21.
Lift up the saddle. Unplug the terminals.
Unscrew the battery fastener.
31 • Push the battery clamp in the direction the
arrow points (1). Remove the battery clamp (2).
32 • Replace the battery.
33 • nsert the battery plug into the special opening in
the battery clamp. Re-position and screw down
the battery clamp. Close and fasten the saddle.
CHARGING THE BATTERY
WARNING: BATTERY CHARGING AND ANY
OTHER WORK ON THE ELECTRICAL SYSTEM
MUST BE CARRIED OUT BY ADULTS.
THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
34 • Unplug vehicle wiring terminal A from battery
terminal B, by pressing terminals on side and
pulling apart.
35 • Plug the battery charger terminal to a wall
outlet following the instruction enclosed.
Connect the plug B to the battery charger plug
C.
Once the charge is completed unplug recharger
from wall outlet. Unplug recharger cord terminal
C from battery terminal B.
36 • Plug battery terminal B into vehicle wiring
terminal A.
When finished working on the battery, always
remember to close and fasten the saddle
PEG PEREGO
offers an after-sales assistance service,
directly or through a network of authorized
assistance centres, for any repairs or replacements
and the sale of original spare parts. To contact the
assistance centres refer to the “Assistance Centres”
booklet included in the packaging.
The item’s serial number must always be quoted.
See the page on spare parts to find out how to
identify the serial number.
Peg Perego always strive to best satisfy their
customers' needs. Knowing the opinions of our
customers is therefore very important and valuable
to us. We would be very grateful if, once you have
used the product, you would fill out the
CONSUMER
SATISFACTION QUESTIONNAIRE
which you can find on
the internet at: www.pegperego.com , making
any observations or suggestions you might have.
CUSTOMER SERVICE