PEERLESS Partner PP-120 Скачать руководство пользователя страница 15

14

Annual Maintenance Activities

Date Last Completed

Piping

1st Year

2nd Year

3rd Year

4th Year

Near heater piping

Check heater and system piping for any sign of leakage; make sure 

pipes are properly supported.

System
Visual

Do a full visual inspection of all system components. Ensure all 

components (including boilers, water treatment systems, mixing 

valves, circulators, etc.) are operating properly and have been 

maintained.

Functional

Test all functions of the system. Perform any maintenance required 

by local codes. Verify system pressure is in the safe operating range.

Temperatures

Check control for temperature accuracy.

*Verify safe settings on Mixing Valve (if installed in system).

Electrical
Smoke and CO 

Detectors

*Verify devices are installed and working properly. Change batteries 

if necessary.

Circuit Breakers

Check to see that the circuit breaker is clearly labeled. Exercise circuit 

breaker.

Connections

Check wire connections. Make sure they are tight.

Relief and Drain Valve
Relief Valve

Lift and release the relief valve on the water heater. Make certain 

that the valve operates properly by allowing several gallons to flush 

through the discharge line. Replace if valve is blocked or does not 

operate properly.

NOTE: TAKE CAUTION WHEN OPERATING RELIEF VALVE. DISCHARGED 

WATER MAY PRESENT A SCALD RISK. 

Drain Valve

Open the drain valve and drain a few quarts of water from the bottom 

of the tank to flush any hard water deposits. Replace if valve is blocked 

or does not operate properly.

NOTE: TAKE CAUTION WHEN OPERATING DRAIN VALVE. DRAINED 

WATER MAY PRESENT A SCALD RISK. 

Final Inspection
Check for 

Combustibles

Check area around heater for combustible materials such as gasoline 

or paint thinner. If combustible materials are found, move away from 

the heater to a safe location.

Checklist

Verify that you have completed the entire checklist. WARNING: 

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.

Homeowner

Review what you have done with the homeowner.

Initial and Date after Inspection / Service. Continue Inspections Annually beyond the 

Fourth Year.

Table 5 - Maintenance Activities Checklist - *If Applicable to System

Part 6 - Maintenance and Troubleshooting

Periodic maintenance should be performed by a qualified service technician to ensure all equipment is operating safely and efficiently. The 

owner should make necessary arrangements with a qualified heating contractor for periodic maintenance of the heater. Installer must also 

inform the owner that the lack of proper water heater care and maintenance may result in hazardous conditions.

Содержание Partner PP-120



















Отзывы: