manualshive.com logo in svg

Peavey PVX p 10, Руководство пользователя

Поделиться
Скачать
Peavey PVX p 10 Скачать руководство пользователя страница 4

Loudspeaker System Specifications 

2 

*   

Each channel has a level control and a 3-band EQ section to adjust and 

shape the input signals 

*   

Mix/Thru Output is via a male XLR jack 

*   

Durable plastic injection-molded trapezoidal enclosure 

*   

Extra angled section on right side allows floor monitor use 

*   

Full-coverage heavy-duty perforated steel grilles, with powder coat finish 

*   

Pole mount molded-

in for 1 3/8” diameter poles 

*   

Top and bottom flying point inserts 

 
 
Description 

 

The 

PVX™p 10 Bluetooth® is a two-way sound reinforcement system based on 

a heavy-duty Pro 10 10

” woofer and a RX™10 titanium diaphragm dynamic 

compression driver mounted on a 100 by 60 degree coverage Quadratic Throat 
Waveguide™.   It’s sleek, modern appearance coupled with excellent 
performance, offer a superb overall package. 
 
The lightweight yet rugged injection-molded plastic enclosure with molded-in 
stand mount cup facilitates portable use for live music or PA sound.  The 
trapezoidal cabinet has two handles for ease of portability, and an extra 45-
degree angled section on the right side to allow use as a floor monitor.  

Four sets 

of flying/mounting points, two sets on the top, two sets on the bottom, and one single 
insert on the rear near the bottom, with a total of 13 cabinet inserts, provide for the 
ultimate in installation flexibility. 

A pair of black powder coated perforated steel 

grilles provides driver protection and a professional appearance. 
 
The heavy-duty 10

” woofer has a 2 3/8" voice coil diameter, and a 50 oz. magnet 

for chest-pounding bass.  The 

RX™10 compression

 

driver tweeter is coupled to 

a Quadratic Throat

™ constant directivity waveguide.  The Quadratic Throat 

Waveguide™ is an original Peavey® design, with smooth, even response, low 
distortion and good high frequency dispersion.  This horn has an asymmetrical 
vertical polar response, aiming the main energy lobe down 10 degrees, so it is 
aimed at the audience, instead of over their heads.  The vertical polar pattern is 
+20 degrees, -40 degrees.  This helps reduce ceiling reflections for greater clarity 
and gain before feedback.   
 
The 

PVX™p 10 Bluetooth® speaker system power amplifiers providing the bi-

amplification are low-distortion reliable fan-cooled units providing a total of 520W 
peak dynamic power for the system. 
There is 400W peak dynamic power for the woofer, and 120W peak dynamic 
power for the tweeter.  The power supply for both amps is a switch mode type for 
low weight and high efficiency.  Both amplifiers feature sophisticated DSP based 
signal compression, which virtually eliminates audible power amplifier clipping.  
Cooling is provided via a low-noise fan, for reliable operation under any 
conditions.  

Содержание PVX p 10














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды