Peavey PVX p 10 Скачать руководство пользователя страница 33

Страница: 33 / 45

Loudspeaker System Specifications

Auto Link

If it is desired that the

PVX™p speakers link all of the time as part of a

permanent setup, the two speakers can be set to automatically link every time
they are turned on.



On each

PVX™p speaker (Primary and Secondary), navigate to the

"Config" screen. See the Config Menu section below this section.



Change the "Auto Link" setting from "Off" to "On".

Fig. 43

Fig. 44

To stop the Auto Link feature, simply turn it back to "Off" on each speaker.

Bluetooth Connection Instructions:

Streaming Audio



On the

PVX™p speaker, navigate to the Bluetooth® screen (BT

header and subsequent menu, Fig. 33, 34)



Set Streaming to "On"



The

PVX™p speaker's Bluetooth® LED (8) will start blinking



On your Bluetooth® device, navigate to Bluetooth® settings



Select PVXp speaker



The Bluetooth® device should change from "Not Connected" to

"Connected"



Once connected, the

PVX™p speaker Bluetooth LED (8) will light

solid.

App Control



In the Bluetooth® App Control menu, change the

PVX™p speaker's

"App Control" from "Off" to "On".



Open the App on your Bluetooth® device. The speaker should

connect automatically.



The

PVX™p speaker Bluetooth® LED (8) will light solid.



The connected speaker will be listed at the top of the App in the

Device list.

Bluetooth® Range Information

Содержание PVX p 10














































Результаты поиска

Содержание PVX p 10

Отзывы:

Бренды по названию

Популярные бренды

Peavey PVX p 10, Руководство пользователя

Результаты поиска

Содержание PVX p 10

Отзывы:

Бренды по названию

Популярные бренды