- 11 -
- 12 -
HH CONTROL
6
HI HAT
5
TOM3
4
TOM2
4
TOM2
2
SNARE
1
KICK
ON
9V AC
OFF
7
CRASH
8
RIDE1
9
RIDE2/ACC1
10
ACC2
11
ACC3
12
ACC4
MIDI OUT
MIDI IN
USB
AUX IN R
AUX IN L
AUX OUT
MAIN OUT
R
2
L
1
POWER
SETTING THE DRUMS ON THE RACK
BASS DRUM
Position the Bass Drum upright and set the Bass Drum
Spurs as shown with the front of the drum about an inch
off the floor (Fig. 15).
The Bass Drum Spurs have spike tips (for added slip
resistance) that can be exposed by turning the Lock Nut
and Rubber Tip clockwise (Fig. 15).
TOM TOM
Make sure that the Tom Holders and the Pipe Clamps are
securely attached. Attach the Toms to the Tom Holders
and position the height and angles to your preference.
When done, set the tab on the StopLock into the slot in
the Pipe Clamp and Tom Holder Bracket and tighten the
Key Bolts with the provided Drum Key to retain the angle
and height settings (Fig. 16).
SNARE STAND/DRUM
Open the legs of the stand to form a stable tripod and
insert the Top Section into the base.
Open the basket and adjust the Butterfly Nut as needed
to accommodate the snare drum.
Place the snare drum into the basket and tighten the
Butterfly Nut to hold the drum securely (do not
overtighten) (Fig. 17).
ASSEMBLYING THE r.e.d.box Module
*Use the spikes only on thick carpeted surfaces to prevent
damage to the flooring underneath.
1. Attach the r.e.d.box Mount to the bottom of the
r.e.d.box as shown using a screwdriver. Do not
overtighten (Fig. 18).
2. Insert the Mount into the Universal Clamp and tighten
the Wing Nut (Fig. 19). Note: Keep the jaws of the
clamp parallel.
3. Adjust the height and angle of the r.e.d. box Module to
your preference.
*Make sure all bolts and nuts are tighten after setting.
Caution
Warning
ASSEMBLYING THE CYMBAL HOLDER
1. Unscrew the Wing Nut on the Cymbal Holder and
detach the Felt Washer. Put both aside for now.
2. Attach the Cymbal Mount onto the Cymbal Post and
rotate the Attachment Screw until it's at a right angle to
the Cymbal Holder Tilter as shown (Fig. 20).
3. Tighten the Attachment Screw with the provided Hex
Wrench.
Note
*The Cable Harness has two sides, one bundled together and the other separated.
WIRING THE CABLE HARNESS
1. Each cable is marked with the name of the component it connects to. Take the bundled side and match the cable to
its correcponding jack on the back side of the r.e.d.box (Fig. 21).
NOTE: The Ride Cymbal has two Jacks. Make
sure to insert the cables into the correct Jacks
2. Take the separated side and match the cable to its corresponding component.
3. Use the provided Velcro Straps to secure the cables to the rack for a clean look.
Fig.19
Fig.20
Fig.21
Fig.18
Fig.15
Fig.16
Fig.17
Spike
Tom Holder
StopLock
Tom Holder Bracket
StopLock
Pipe Clamp
Butterfly Nut
r.e.d.box
Mount
Universal Clamp
Screw
Cymbal Mount
Cymbal Post
Cymbal Holder tilter
Attacment Screw
Rubber Tip
Lock Nut
Spur
sample
