background image

PEAK® IOM57 Input/Output Modules Installation Instructions

6

SA/FC bus terminal block

You can connect an IOM to an SA bus or an FC bus, but not to both buses simultaneously. The SA/FC bus terminal 
block is a removable, 4-terminal plug that fits into a board-mounted jack.

When you connect the IOM to an FC bus, wire the bus terminal block plugs on the controller and the other 
controllers in a daisy-chain configuration using 3-wire twisted, shielded cable as shown in Figure 4. See Table 6 for 
more information.

When you connect the IOM to an SA bus, wire the bus terminal block plugs on the controller and other SA bus 
devices in a daisy-chain configuration using 4-wire twisted, shielded cable as shown in Figure 5. See Table 4 for 
more information.

Note:

The SA PWR/SHLD terminal does not supply 15 VDC. The SA PWR/SHLD terminal is isolated and you can 

use the terminal to connect (daisy chain) the 15 VDC power leads on the SA bus (Figure 5) or the cable shields on 
the FC bus (Figure 4). The SA bus supervisor advanced application field equipment controller (FAC), field 
equipment controller (FEC), or VAV modular assembly (VMA) supplies 15 VDC to devices on the SA bus that 
require power.

SA/FC bus port

The SA/FC bus port on the front of the controller is an RJ-12, 6-position modular jack that provides a connection for 
devices on the SA bus, a Wireless Commissioning Converter, ZigBee® wireless dongle, or a ZFR1811 Wireless 
Router, depending on which bus the IOM is operating on.

Figure 4:  FC bus terminal block wiring

 Stranded 3-Wire Twisted Shielded Cable

Isolated Shield

Connection

Terminal

+

_

CO

M

SH

L

D

To Next

Device on

the FC Bus

Segment

FC Bus

Terminal

Block Plugs

F

IG

: f

c_

bus

_t

er

m

s

+

_

CO

M

SH

L

D

Terminating Device

on FC Bus Segment

To Next

Device on

the FC Bus

Segment

Daisy Chained Device 

on FC Bus Segment

Figure 5:  SA bus terminal block wiring

 Stranded, 4-Wire (2 Twisted Pair) Shielded Cable

(One twisted pair is the   and  leads. 

+

 

-

The second pair is COM and SA PWR.) 

Cable Shield

Connection

To Next

Device on

the SA Bus

F

IG

:s

a_b

us

_t

er

m

s

SA Bus

Terminal

Block Plugs

Terminating Device

on SA Bus

Daisy Chained Device 

on SA Bus

To Next

Device on

the SA Bus

+

CO

M

SA

 PW

R

+

CO

M

SA

 P

W

R

Содержание PEAK IOM57






















Отзывы: