Peak Scientific MS Table Series Скачать руководство пользователя страница 3

Page 3

Safety Notices

Peak Scientific Instruments cannot anticipate every possible circumstance which may 

represent a potential hazard. The warnings detailed within this document detail the 

most known potential hazards, but by definition cannot be all inclusive. If the user 
employs an operating procedure, item of equipment or a method of working which 

is not specifically recommended by Peak Scientific, the user must ensure that the 
equipment will not be damaged or become hazardous to persons or property.

Symbols

This document uses the following symbols to highlight specific areas important to the 
safe and proper use of the Generator

A WARNING notice denotes a hazard. It calls attention to an operating procedure, 

process or similar, which if not correctly performed or adhered to, could cause 

personal injury or in the worst case death. Do not proceed beyond a WARNING 

notice until the indicated conditions are fully understood or met.

A CAUTION notice denotes a hazard. It calls attention to an operating procedure, 

process or similar, which if not correctly performed or adhered to, could cause 

damage to the Generator or the Application. Do not proceed beyond a CAUTION 

notice until the indicated conditions are fully understood or met. 

Caution, risk of electric shock. Ensure power to the Generator has been removed 

before proceeding.

Safety Notice to Users

These instructions must be read thoroughly and understood before 

installation and operation of your Peak Generator. Use of the generator 
in a manner not specified by Peak Scientific MAY impair the SAFETY 
provided by the equipment. 

When handling, operating or carrying out any maintenance, personnel 

must employ safe engineering practices and observe all relevant local 
health and safety requirements and regulations. The attention of UK 
users is drawn to the Health and Safety at Work Act 1974, and the 
Institute of Electrical Engineers regulations.

If the equipment is used in a manner not specified by the manufacturer, 
the protection provided by the equipment may be impaired.

WARNING

WARNING

WARNING

WARNING

CAUTION

Page 3

Содержание MS Table Series
















Отзывы: