PCM SAL-DLG FIREWOR-X-TEND Скачать руководство пользователя страница 6

Страница: 6 / 18

Firewor-X-tend Building instruction January 2009

5. Stabilizer

5.1 Installation of the CFR-stab

Sand the rudder

wedge-shaped

on the

hinge line

, so that you can move it in both directions. Note

that the

hinge line

must be placed

on the left side

(looking towards flight direction) for

right-

handers

and the other way round for left-handed persons.

Next, glue the

lever

in extension of the axis of the boom. The

hole of the lever

should be

above

the hinge line

. Fix the control surface of the rudder with

adhesive tape

Before you fix the stabilizer to the fuselage, thread the

kevlar wire through the boom

to the hole in the fuelage

cone.

Then,

check

the

good fit

of the rudder. The axis of the

boom should be right-angled to the hinge line of the rudder.
The kevlar wire should not chafe on the sharp carbon. It
must be free movable.

Sand the part of the boom which will be positioned in the
stab and about 1-2cm before.

If the stabilizer is

aligned correctly

on each axis, let

super

glue

run into the upper and lower join from both sides. Pay

attention to the

kevlar wire

, so that it keeps

free movable

Last, glue the

two carbon covers

left and right of the join

also with super glue. Note, that the hole for the installation
of the elevator must be kept open.

www.pcm.at

Содержание SAL-DLG FIREWOR-X-TEND



















Результаты поиска

Содержание SAL-DLG FIREWOR-X-TEND

Отзывы:

Бренды по названию

Популярные бренды

PCM SAL-DLG FIREWOR-X-TEND, Инструкция по сборке

Результаты поиска

Содержание SAL-DLG FIREWOR-X-TEND

Отзывы:

Бренды по названию

Популярные бренды