PCE Health and Fitness DeBurr-It! 248-3 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 17

background image

7

Runout adjustment hardware

To adjust run out loosen all three lockscrews a few turns.

All new belts and re-tensioned belts will always slightly run off the idler wheel. After changing or retensioning,
turn the Belt Runout Adjustment slightly clockwise. Turn on the sander. Adjust the Belt Runout Adjustment
until the belt is centered on the top crowned idler.

!!IMPORTANT!! – DO NOT RUN THE BELT FOR AN EXCESSIVELY LONG TIME WITH IT BIASED EXTREMELY TO
ONE SIDE OR THE OTHER OF ANY OF THE PULLEYS. DAMAGE TO RUNNING COMPONENTS AND/OR FRAME
WILL OCCUR.

While the machine is still on retighten the lockscrews finger tight. The belt is adjusted.

«
...
5
6
7
8
9
...
»

Содержание DeBurr-It! 248-3


















Отзывы:

Нет отзывов

Похожие инструкции для DeBurr-It! 248-3

Бренд: Parkside Страницы: 64

Бренд: GreenWorks Страницы: 52

Бренд: F.F. Group Страницы: 60

Бренд: Status Страницы: 26

Бренд: Powermate Страницы: 16

Бренд: HSS Hire Страницы: 2

MINI RANDOM ORBITAL SANDER

Бренд: 3M Страницы: 6

Бренд: 3M Страницы: 22

Бренд: FAR Страницы: 14

Бренд: Raider Страницы: 92

Бренд: Parkside Страницы: 7

Бренд: Makita Страницы: 32

Power Tools SA19/S.V2

Бренд: Sealey Страницы: 3

Бренд: BN Products Страницы: 8

PRO-POWER VILR900

Бренд: VITO Страницы: 48

Бренд: Grizzly Страницы: 3

Бренд: wurth Страницы: 95

Бренд: VONROC Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды