PCE Health and Fitness DeBurr-It! 248-3 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 17

background image

12

Variable Speed Drive

A variable speed drive option will let you increase or decrease the speed of the motor. We always recommend
using our supplied VFD with the correct parameters already setup for safe operation of the sander. NEVER use
a rheostat to control the speed of any single or polyphase AC induction motor. Please consult DeBurr-It!
technical department if you are using a non supplied VFD.

If no FORWARD/REVERSE control operator is supplied, jump the terminals “COM” to the desired direction.

!!IMPORTANT!! – NEVER OVERRIDE DEFAULT DEBURR-IT! PARAMETER SETTINGS WITHOUT CONSULTING
DEBURR-IT! TECHNICAL DEPARTMENT.

All parameters have been throroughly tested and changing any parameters will void any safety or warranty
conditons.

«
...
10
11
12
13
14
...
»

Содержание DeBurr-It! 248-3


















Отзывы:

Нет отзывов

Похожие инструкции для DeBurr-It! 248-3

Бренд: Zenit Powertools Страницы: 10

Бренд: Ryobi Страницы: 12

Бренд: Jet Страницы: 19

Бренд: Grizzly Страницы: 32

Бренд: Dualtools Страницы: 22

Бренд: Feider Machines Страницы: 17

Бренд: Erbauer Страницы: 17

Бренд: Ingersoll-Rand Страницы: 38

Бренд: Hakki Pilke Страницы: 47

Бренд: Far Tools Страницы: 22

Бренд: Ratio Страницы: 40

Бренд: Jet Страницы: 2

Бренд: EINHELL Страницы: 88

Бренд: Makita Страницы: 41

Бренд: Makita Страницы: 44

Бренд: Craftsman Страницы: 8

Бренд: Craftsman Страницы: 14

Бренд: Craftsman Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды