PCB Piezotronics 208A11, Инструкция по установке и эксплуатации

Страница: 16 / 17

Model Number
208A11
ICP® FORCE SENSOR
Revision: K
ECN #: 45224
Performance ENGLISH SI
Sensitivity(± 15 %) 500 mV/lb 112,404 mV/kN
Measurement Range(Compression) 10 lb 0.04448 kN
Measurement Range(Tension) 10 lb 0.04448 kN
Maximum Static Force(Compression) 60 lb 0.270 kN
Maximum Static Force(Tension) 60 lb 0.270 kN
Broadband Resolution(1 to 10,000 Hz) 0.0001 lb-rms 0.0004448 N-rms [2]
Low Frequency Response(-5 %) 0.01 Hz 0.01 Hz [3]
Upper Frequency Limit 36,000 Hz 36,000 Hz [4]
Non-Linearity ≤ 1 % FS ≤ 1 % FS [5]
Environmental
Temperature Range -65 to +250 °F -54 to +121 °C
Temperature Coefficient of Sensitivity ≤ 0.05 %/°F ≤ 0.09 %/°C
Electrical
Discharge Time Constant(at room temp) ≥ 50 sec ≥ 50 sec
Excitation Voltage 18 to 30 VDC 18 to 30 VDC
Constant Current Excitation 2 to 20 mA 2 to 20 mA
Output Impedance ≤ 100 Ohm ≤ 100 Ohm
Output Bias Voltage 8 to 12 VDC 8 to 12 VDC [1]
Output Polarity(Compression) Positive Positive
Physical
Stiffness 6 lb/µin 1.05 kN/µm [2]
Size (Hex x Height) 0.625 in x 1.17 in 15.88 mm x 29.7 mm
Weight 0.80 oz 22.7 gm
Housing Material Stainless Steel Stainless Steel
Sealing Epoxy Epoxy
Electrical Connector 10-32 Coaxial Jack 10-32 Coaxial Jack
Electrical Connection Position Axial Axial
All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.
ICP
®
is a registered trademark of PCB Group, Inc.
N
- Negative Output Polarity
Output Polarity(Compression) Negative Negative
W
- Water Resistant Cable
Electrical Connector Sealed Cable Sealed Cable
NOTES:
[1]Sensor contains protected electronics which may cause long 'turn-on" times.
[2]Typical.
[3]Calculated from discharge time constant.
[4]Estimated using rigid body dynamics calculations.
[5]Zero-based, least-squares, straight line method.
[6]See PCB Declaration of Conformance PS023 for details.
SUPPLIED ACCESSORIES:
Model 080A81 Thread Locker (1)
Model 081B05 Mounting Stud (10-32 to 10-32) (1)
Model 084A03 Impact Cap (1)
Model M081A62 Mounting stud, 10-32 to M6 x 1, BeCu with shoulder (1)
3425 Walden Avenue, Depew, NY 14043
Phone: 716-684-0001
Fax: 716-684-0987
E-Mail: info@pcb.com
[6]
OPTIONAL VERSIONS
Optional versions have identical specifications and accessories as listed for the standard model
except where noted below. More than one option may be used.
Entered: LK Engineer: MJK Sales: KWW Approved: APB Spec Number:
Date: 3/30/2016 Date: 3/30/2016 Date: 3/30/2016 Date: 3/30/2016
208-1110-80