background image

16

Technical Reference Booklet

Primary

These categories identify the types of the two channels that

Master/Primary

have been installed in the computer. There are 45 predefined

Slave/Secondary types and one user definable types in BIOS. Type 1 to Type 45 are
Master/Secondary  predefined. Type “user” is user-definable.
Slave

Press PgUp or PgDn to select a numbered hard disk type
or type the number and press <Enter>. Note that the
specifications of your drive must match with those of the
drive table. The hard disk will not work properly if you enter
improper information for this category. If your hard disk drive
type is not matched or listed, you can select Type “User” to
define your own drive type manually.

If you select Type “User”, you will need to know the
information listed below. Enter the information directly from
the keyboard and press <Enter>. This information should
be included in the documentation from your hard disk vendor
or the system manufacturer.

If the controller of the HDD interface is ESDI, the selection
shall be “Type1”.

If the controller of the HDD interface is SCSI, the selection
shall be “None” .

If you select Type “Auto”, the BIOS will auto-detect the HDD
and CD-ROM drive at the POST stage and show the IDE for
the HDD and CD-ROM drive.
TYPE

-Drive type

CYLS

-Number of cylinders

HEADS

-Number of heads

PRECOMP

-Write precom

LANDZONE

-Landing zone

SECTORS

-Number of sectors

MODE

-Mode type

If a hard disk has not been installed, select NONE and
press <Enter> .

Drive A Type /

This category identifies the types of floppy disk drive A or

Drive B Type

drive B that has been installed in the computer.

Video

This category selects the type of video adapter used for the
primary system monitor. Although secondary monitors are
supported, you do not have to select them in Setup.

BIOS  Features Setup

This section allows you to configure your system for basic operation. You have
the opportunity to select the system’s default speed, boot-up sequence,
keyboard operation, shadowing and security.

Содержание 35889700 Series





















Отзывы: