background image

 

General warning 

 

• 

Read this guide carefully before use.

 

• 

Before APEX 7000 is installed, check voltage compatibility with the Vending Machine.

 

• 

The product has been designed as internal equipment.

 

• 

Do not use in water or near liquids where it might become wet.

 

• 

Do not use near smoke or inflammable gases.

 

• 

Cut power before maintaining electrical and/or mechanical components.

 

• 

Dispose of the device in accordance with environmental laws (DO NOT burn).

 

• 

Always read labels.

 

• 

Do not tie the system main cables or cables belonging to slave units.

 

• 

Periodically check whether cables are correctly plugged on their connectors.

 

• 

Cut power before maintaining and/or cleaning the unit.

 

• 

Use a damp cloth to clean plastic elements.

 

 

 

Product overview 

 

APEX 7000 is a MDB Bill Acceptor, meeting the standards required by MDB protocol. 

The product is available with 200 bill- and 500 bill-stacker. 

The  “Escrow”  function  enables  users  to  get  the  bill  back  in  the  case  of  a  failed  vend  or  when  no  change  is 
available. 

The  bill  validation  module  can  be  removed  to  make  cleaning  operations  easier.  An  optical  anti-stringing 
technology.grants the highest security. 

It is possible to enable single bills quickly by toggling the DIP switches on board. 

The product is equipped with pushbutton for diagnostic purposes and front bezel lights for a correct interpretation 
of diagnostic signals (the number of times the lights flash corresponds to the error code). 

Apex 7000 can the updated with the handheld device PRO-2. 

 

 

Technical description 

 
Operating voltage: 

34V DC unstabilized (rectified and filtered) 

 

24V DC rms (rectified) 

Voltage rate: 

20V DC min.; 40V DC max. 

Operating currents: 

180 mA (idle), 500 mA (accepting), 1,50 A (stalled) 

Operating temperature: 

0°C – 60°C, 90% non-condensing humidity. 

Acceptance rate: 

> 95% including second time insertion of a rejected bill. 

Acceptance speed: 

approx. 20 bills per minute 

Sensor array: 

8 Optical Sensors 

Bills accepted: 

up to 12 bills in all four directions - up to 72 mm wide 

Net weight: 

2.3 lbs./1.04 kg

 (with 200-bill stacker) 

Stacker capacity: 

200 (standard) or 500 bills 

 

 

 

 

 

 

 

Содержание Apex 7000













Отзывы: