Payne PG9MXA Series Скачать руководство пользователя

Страница: 18 / 62

18-IN. (457.2 mm)

MINIMUM TO BURNERS

A93044

Fig. 17 -- Installation in a Garage

NON-DIRECT VENT (1-PIPE) APPLICATION

UNIT DAMAGE HAZARD

Failure to follow this caution may result in intermittent

unit operation.
Do not install furnace in a corrosive or contaminated

atmosphere. Make sure all combustion and circulating air

requirements are met.

CAUTION

Refer to the AIR FOR COMBUSTION AND VENTILATION

section for details.

AIR FOR COMBUSTION AND

VENTILATION

Provisions for adequate combustion, ventilation, and dilution air

must be provided in accordance with:

U.S. Installations:

Section 9.3 NFPA 54/ANSI Z223.1--2006,

Air for Combustion and Ventilation and applicable provisions
of the local building codes.

Canadian Installations:

Part 8 of CAN/CS----B149.1--05.

Venting Systems and Air Supply for Appliances and all
authorities having jurisdiction.

FURNACE CORROSION HAZARD

Failure to follow this warning could result in reduced furnace

component life.
Air for combustion must not be contaminated by halogen

compounds, which include fluoride, chloride, bromide, and

iodide. These elements could corrode heat exchangers and

shorten furnace life. Air contaminants are found in aerosol

sprays, detergents, bleaches, cleaning solvents, salts, air

fresheners, and other household products.

WARNING

The following types of furnace installations may require

OUTDOOR AIR for combustion due to chemical exposures:

Commercial buildings

Buildings with indoor pools

Laundry rooms

Hobby or craft rooms, and

Chemical storage areas

If air is exposed to the following substances, it should not be

used for combustion air, and outdoor air may be required

for combustion:

Permanent wave solutions

Chlorinated waxes and cleaners

Chlorine based swimming pool chemicals

Water softening chemicals

De-icing salts or chemicals

Carbon tetrachloride

Halogen type refrigerants

Cleaning solvents (such as perchloroethylene)

Printing inks, paint removers, varnishes, etc.

Hydrochloric acid

Cements and glues

Antistatic fabric softeners for clothes dryers

Masonry acid washing materials

All fuel-burning equipment must be supplied with air for fuel

combustion. Sufficient air

must

be provided to avoid negative

pressure in the equipment room or space. A positive seal

must

made between the furnace cabinet and the return-air duct to

prevent pulling air from the burner area and from draft

safeguard opening.

CARBON MONOXIDE POISONING HAZARD

Failure to follow this warning could result in personal injury

or death.
The operation of exhaust fans, kitchen ventilation fans, clothes

dryers, attic exhaust fans or fireplaces could create a

NEGATIVE PRESSURE CONDITION at the furnace.

Make-up air MUST be provided for the ventilation devices, in

addition to that required by the furnace. Refer to the Carbon

Monoxide Poisoning Hazard warning in the venting section of

these instructions to determine if an adequate amount of

make-up air is available.

WARNING

The requirements for combustion and ventilation air depend upon

whether or not the furnace is located in a space having a volume

of at least 50 cubic feet per 1,000 Btuh input rating for all gas

appliances installed in the space.

Spaces having less than 50 cubic feet per 1,000 Btuh require
the

OUTDOOR COMBUSTION AIR

METHOD.

Spaces having at least 50 cubic feet per 1,000 Btuh may use
the

INDOOR COMBUSTION AIR, STANDARD or

KNOWN AIR INFILTRATION

METHOD.

Outdoor Combustion Air

Method

1. Provide the space with sufficient air for proper

combustion, ventilation, and dilution of flue gases using

permanent horizontal or vertical duct(s) or opening(s)

directly communicating with the outdoors or spaces that

freely communicate with the outdoors.

2. Fig. 18 illustrates how to provide TWO OUTDOOR

OPENINGS, one inlet and one outlet combustion and

ventilation air openings to the outdoors.

a. One opening

MUST

commence within 12 in. (305

mm) of the ceiling and the second opening MUST

commence within 12 in. (305 mm) of the floor.

b. Size openings and ducts per Fig. 18 and Table 1.

c. TWO HORIZONTAL DUCTS require 1 square inch of

free area per 2,000 Btuh (1,100 mm

/kW) of combined

input for all gas appliances in the space per Fig. 18 and

Table 1.

d. TWO OPENINGS OR VERTICAL DUCTS require 1

square inch of free area per 4,000 Btuh (550 mm

/kW)

for combined input of all gas appliances in the space

per Fig. 18 and Table 1.

3. ONE OUTDOOR OPENING requires:

a. 1 square inch of free area per 3,000 Btuh (734 mm

/kW)

for combined input of all gas appliances in the space

per Table 1 and 13.

Содержание PG9MXA Series































































Результаты поиска

Содержание PG9MXA Series

Отзывы:

Похожие инструкции для PG9MXA Series

Бренды по названию

Популярные бренды

Payne PG9MXA Series, Инструкция по установке, запуску и эксплуатации

Результаты поиска

Содержание PG9MXA Series

Отзывы:

Похожие инструкции для PG9MXA Series

Бренды по названию

Популярные бренды