manualshive.com logo in svg

Paxton Switch2, Руководство по установке

Поделиться
Скачать
Paxton Switch2 Скачать руководство пользователя страница 23

Using function cards – Starter pack 

Order card 
This card is not used in all card packs.  If present, it needs to be sent back with an order 
form if more cards are needed. (See order form located in the card pack for more details) 
Enrolment card 
This card is used to both initialise the system and re-enrol barred users. It can be swiped 
through once to initialise the system after it is first powered up (See Initialising the 

system).  
If a user has been barred from a door and needs to be re-enrolled the enrolment card is 
used with the user card.  

• 

First swipe the enrolment card through the reader (The 

AMBER

 LED will flash and 

the 

RED

 and 

GREEN

 LED will go out. The control unit will continually beep) 

 

• 

Swipe the user card within 60 seconds. The control unit will stop beeping and the 

LEDs will return to their normal state.  The user card will now be granted access. 

 

Door Open Time card 
This card is used to adjust the time the relay is powered. To change the time  

• 

Swipe the card once (all the LEDs go out and the arrow LED flashes. The Switch2 

control unit will then beep once per second) 

• 

Swipe the card again after the desired interval (all the LEDs come back on) 

 

Silent Operation card 
This card is used to toggle the beeping of the Switch2 control unit on and off. By default 
the Switch2 control unit beeps when a user card is swiped. If necessary this beep can be 

silenced by swiping the silent operation card through the reader.  
After the card has been swiped the LEDs will go out and the 

GREEN

 arrow LED stays on. 

The unit beeps twice and all the LEDs will come on again. Now the Switch2 control unit 
will not beep when a user card is swiped. To return to normal operation again, swipe 

through the silent operation card again. 
Fail Open Release card 
This is not required for Switch2.  (The relay has NO and NC connections – see Diagram) 

 

Using function cards – Function card pack 

GREEN

, 

AMBER

 and 

RED

 Zone cards 

These 3 cards toggle the 

GREEN

, 

AMBER

 and 

RED

 access levels on and off. By default all 

the levels are active (this means all the LEDs are lit up on the reader). This in turn allows 
users with 

GREEN

, 

AMBER

 and 

RED

 user cards access through this particular entrance. 

If you wish to bar users from a particular colour zone, for example 

GREEN,

 take the 

GREEN

 zone card and swipe it through the reader. The 

GREEN

 LED will go out and the 

reader will beep. All 

GREEN

 user cards will now be barred.  To re-enable these users, 

swipe the 

GREEN

 zone card again and the 

GREEN

 LED will come back on. 

This happens for each colour zone card and its corresponding colour LED. 
Remote Release card 
This card is not used with Switch2. 
Card Plus PIN card 
This card is not used with Switch2. 

Chapter 5   Operation 

23  

Содержание Switch2






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды