manualshive.com logo in svg

Paxton Switch2, Руководство по установке

Поделиться
Скачать
Paxton Switch2 Скачать руководство пользователя страница 22

CARDLOCK & PROXIMITY 

* IMPORTANT *  

CARDLOCK or PROXIMITY 
In all the explanations below, the actions for a CARDLOCK system have been used.  
These actions are also used with the PROXIMITY system except that the instead of the 
action “Swiping” a card for a CARDLOCK reader, the term “presenting” a PROXIMIY card 

applies to PROXIMITY.  
As you may notice there is no Arrow LED on the PROXIMITY reader and so any note 

about this can be ignored with PROXIMITY.  Also, ALL PROXIMITY readers have a fixed 
sounder. This means they will always beep if a PROXIMITY card is presented to them. 
 
PROXIMITY vandal proof reader 
There are no LEDs on the vandal proof reader! This means visual indication does not 
apply. The reader will indicate the various actions (presenting a PROXIMITY card etc.) 
with high (accept) or low (reject) beeps. 
 
Initialising the system 
After the system has been wired up, be sure to check over the connections against the 

wiring diagrams provided before powering up for the first time. When the system is 
powered up for the first time the control unit will bleep 3 times a second. This indicates 
that Switch2 is waiting to be initialised. If a CARDLOCK reader is connected the arrow 

LED will also be flashing. 

All the user cards will now work. 
User cards 
These are the cards the everyday user of the system will have. They can gain access 

through a door by presenting the card to the reader. If the corresponding colour LED 
on the reader is lit then the user can enter, assuming they have not been barred. If the 

card is accepted the 

GREEN

 LED will flash (the 

RED

 and 

AMBER

 go out) and the door can 

be opened. If the card is not accepted then the 

RED

 LED will flash (all the other LEDs will 

go out). 
NOTE: The control unit will beep each time a user card is used unless the system is set 
for silent operation. 
Shadow cards 
To bar a user from entering an area guarded by a reader, the shadow card is used.  
Swipe the shadow card through the reader (the reader beeps once and the control unit 

beeps twice). If the barred user now tries to use the reader to gain entrance their access 
will be denied. 
 

Programming Switch2 using function cards 

With the CARDLOCK or PROXIMITY reader connected to Switch2 the function cards are 
used to alter system features. Some function cards come in the starter pack and others 

come in the function card pack. 

Chapter 5   Operation 

22  

Содержание Switch2






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды