Pavilion GQ-C3260WX-FF PB US Скачать руководство пользователя страница 63

Страница: 63 / 68

16 Installation of the Quick Connect

Multi-System

The Quick Connect Multi-System allows the installation of two Water Heaters together utilizing only the Quick

Connect Cord, sold separately.

3-18 in. (76-457

mm)

6 ft (1.8 m)

Distance on sides

Quick Connect Cord

Cold Water

Hot Water

Leave enough clearance around

the plumbing to apply insulation.

It will be necessary to add bends to

the piping to ensure that this

clearance is available.

Service Valve Kit with

Pressure Relief Valve is

necessary for flushing

the Heat Exchanger.

This allows for easy

flushing of the system.

The backflow preventer should

be placed upstream of the cold

water branch.

Size the piping to allow for the

maximum flow rates of the

Water Heaters.

Make this distance ( ) as short as

possible. The hot water temperature

will become unstable as the pipe

length increases.

Service Valve Kit with

Pressure Relief Valve

Typical Plumbing

Insulate or apply heating materials to both the cold water supply piping and the hot water supply piping to

prevent freezing during cold weather and to prevent heat loss through the piping.

Remote Controller Cord

Gas Supply

Cold Water Supply

Hot Water

Remote Controller

External Remote

Terminal Block

Quick Connect

Cord

Connector

Cord

Connector

System Diagram

• Connect a single Remote

Controller to only one of the

Water Heaters.

• Water Heaters must be

same model.

Installation of the Quick Connect Multi-System

Содержание GQ-C3260WX-FF PB US





































































Результаты поиска

Содержание GQ-C3260WX-FF PB US

Отзывы:

Похожие инструкции для GQ-C3260WX-FF PB US

Бренды по названию

Популярные бренды

Pavilion GQ-C3260WX-FF PB US, Руководство по установке

Результаты поиска

Содержание GQ-C3260WX-FF PB US

Отзывы:

Похожие инструкции для GQ-C3260WX-FF PB US

Бренды по названию

Популярные бренды