Pavilion GQ-C3260WX-FF PB US Скачать руководство пользователя страница 28

Страница: 28 / 68

For Vertical Vent Termination - PVC, CPVC or PP Material

Roof Flashing

Storm Collar

Roof

Flashing

Storm

Collar

≥ 3 ft Min.

12 in. over

maximum

snow level

12 in. over

maximum

snow level

Support

Hanger

Strap

2 in. pipe*

3 in. pipe

2 in. × 3 in. Increaser

coupling

• A short horizontal section is

required to prevent debris

from falling into the water

heater.

• When using a horizontal

section, slope the horizontal

vent 1/4 in. upwards for

every 12 in. (305 mm)

toward the termination to

drain condensate.

When the vent

penetrates a floor or

ceiling and is not

running in a fire rated

shaft, a firestop and

support is required.

About the termination

• When choosing intake and exhaust terminations, you must use the same type of elbow (i.e.

both 90° elbows).

This will help with proper combustion by putting both terminations in the same pressure zone.

• Insert Bird Screen in End of 90° Elbow.

Bird Screen is not supplied with water heater, order separately.

• To prevent excessive condensation formation, only the vent termination should be located on

the exterior of the building.

When the vent termination

is located not less than 8 ft

(2.4 m) from a vertical wall

or similar obstruction,

terminate above the roof at

least 2 ft (0.6 m), but not

more than 6 ft (1.87 m), in

accordance with the

National Fuel Gas Code

ANSI Z223.1 / NFPA 54 or

Natural Gas and Propane

Installation Code CSA

B149.1.

Provide vertical

support every 3 ft

(0.9 m) or as

required by the vent

pipe manufacturer's

instructions.

Support

Firestop

2 in. × 3 in. Increaser couplings are

required when using 3 in. (75 mm)

pipe.

• The combustion

air intake of any

appliance

• Any other building

opening

Firestop

* The length of the pipe

between the Increaser

couplings and the Exhaust

and Intake Flue of the

Water Heater should be up

to 6 in. (152 mm).

Exhaust

2 in. (50 mm)

3 in. (75 mm)

Intake

2 in. (50 mm)

3 in. (75 mm)

6.4.3 Vertical Vent Termination

Venting the Water Heater

Содержание GQ-C3260WX-FF PB US





































































Результаты поиска

Содержание GQ-C3260WX-FF PB US

Отзывы:

Похожие инструкции для GQ-C3260WX-FF PB US

Бренды по названию

Популярные бренды

Pavilion GQ-C3260WX-FF PB US, Руководство по установке

Результаты поиска

Содержание GQ-C3260WX-FF PB US

Отзывы:

Похожие инструкции для GQ-C3260WX-FF PB US

Бренды по названию

Популярные бренды