Pavilion GQ-C3260WX-FF PB US Скачать руководство пользователя страница 48

Страница: 48 / 68

Connecting the Remote Controller Cord

1. Check to make sure that the Remote Controller

Cord has plenty of slack in order to reach the

external connection terminal block.

2. Make sure the electrical power is disconnected

from the Water Heater.

3. Open the external remote terminal block.

5. Reattach the terminal block cover.

NOTE

Tie the redundant cord outside the

Water Heater. Do not put the extra

length inside the Water Heater.

2) Pull downward

1) Pinch

10.3 Recirculation Pump

NOTE

This feature is not available when

using the Quick Connect Multi-System

feature.

Connecting the pump control wire
[When using the manufacturer’s Recirculation

System (Recirculation Pump Kit)]

1. Check the electrical power is disconnected from

the Water Heater.

2. Remove the front cover (4 screws).

3. The pump comes pre-assembled with a

wiring harness to be easily connected into the

Water Heater. Feed wiring through the wiring

throughway located at the bottom of the Water

Heater.

4. Locate Connector marked “PUMP” and insert

pump power connector.

Pump Power Cord

Ground Wire

Wiring

Throughway

Pump Control

Wire tag

Clamp

Connector

Circuit Board

PUM

Circuit Board

Pump Control

Wire Tag

Crimping

Terminal

Wiring

Throughway

Supplies Power for

Recirculation Pump

(Use a relay for larger pumps)

Ground Wire

NOTE

A dummy plug is inserted from the

factory. This connector must be

removed before connecting the pump

power connector. Press lightly on the

connector to release the dummy plug.

5. Connect the ground wire (green color wire) to

the screw at the base of the Water Heater.

6. Reattach the front cover (4 screws).

4. Pass the Remote Controller Cord through the

wiring throughway.

Connect the Y-shaped terminals at the end of

the Remote Controller Cord to the terminal

block.

Wiring Throughway

Remote Controller Cord

NOTE

Leave enough slack so that the pump

control wires will stay connected if

the Water Heater is removed from

the wall.

[When not using the manufacturer’s Recirculation

System (Recirculation Pump Kit)]

1. Check the electrical power is disconnected from

the Water Heater.

2. Remove the front cover (4 screws).

3. Cut off the connector at the end of the pump

control wires.

4. Only when using a pump of 100 W or less,

pass the pump power cord through the wiring

throughway and connect with the pump control

wires.

This will be the power supply for the pump.

If a large pump (greater than 100 W) is being

used, use the voltage from these wires as the

signal to close a normally open relay through

which 120 VAC will be supplied directly from a

wall circuit to the pump.

5. Connect the ground wire to the screw at the

base of the Water Heater.

6. Reattach the front cover (4 screws).

Connecting Electricity

Содержание GQ-C3260WX-FF PB US





































































Результаты поиска

Содержание GQ-C3260WX-FF PB US

Отзывы:

Похожие инструкции для GQ-C3260WX-FF PB US

Бренды по названию

Популярные бренды

Pavilion GQ-C3260WX-FF PB US, Руководство по установке

Результаты поиска

Содержание GQ-C3260WX-FF PB US

Отзывы:

Похожие инструкции для GQ-C3260WX-FF PB US

Бренды по названию

Популярные бренды