background image

33..00 

 

 

 

C

CO

ON

NFFIIG

GU

UR

RA

ATTIIO

ON

N

The Model 1088/K is equipped with two sets of eight DIP switches,

which allow configuration of the unit for a wide variety of applications.
This section describes switch locations and explains all possible con-
figurations.

3.1  CONFIGURING THE HARDWARE DIP SWITCHES 

The 16 external switches are grouped into two eight-switch sets,

and are externally accessible from the underside of the Model 1088/K
(See Figure 1, below).   

The two sets of DIP switches on the underside of the Model 1088/K

will be referred to as S1 and S2.  As Figure 2 shows, the orientation of
all DIP switches is the same with respect to “ON” and “OFF” positions.  

5

Figure 2. Close Up of Configuration Switches (all sets are identical in appearance) 

Figure 1. Underside of Model 1088/K, Showing Location of DIP Switches

Front

Rear

On

S1

S2

Off

3.1.1  Configuration DIP Switch Set “S1”

Switches S1-1 through S1-8 may be used to configure CO/CP

operation, line framing and coding, CRC-4 operation, and DTE initiated
loop diagnostics.  Default settings of S1 Switches are shown in the
table below.

Switch S1-1:  CO/CP 

Use Switch S1-1 configure the CO (located at the Central Office or

or G.703/G.704 demarcation point) or CP (located at the Customer
Premises) mode of the 1088/K.

S1-1

CO/CP Mode

Off

CO = located at the Central Office

On

CP = located at the Customer Premises

CO/CP Configuration:

The Model 1088/K does not use clock mode settings as described
in other Patton mDSL products. Instead, the Model 1088/K will
always recover the clocking from the G.703/4 network and use this
clock to send data across the DSL span to the remote DSL
modem, which will  use the incoming to send data out to G.703/4
network.  Therefore, one unit must be set for CO mode (located at
the G.703 demarcation), and the other unit must be set for CP
mode (located at the customer premises).  This type of clocking
method was employed for two reasons:

1) To allow two independent networks to use the modems as inde-

pendent clocking paths.

2) To allow the user to independently specify the timing source for

the network based on external equipment.

6

Position

Function

S1-1

CO/CP Setting

On

CP Mode

S1-2

Line Coding

Off

HDB3 

S1-3

CRC-4 Enable

Off

Disabled

S1-4

Reserved

Off

S1-5

Reserved

On

S1-6

Reserved

Off

S1-7

Reserved

On

S1-8

Reserved

Off

 

Factory Default

S1 SUMMARY TABLE

OFF

ON

Содержание 1088


















Отзывы: