Patton electronics RS-232 Скачать руководство пользователя страница 4

SWITCH SET SW1

The configuration switches on switch set SW1 set analog

loopback, digital loopback and V.54 enable/disable.  The default
settings are summarized in Figure 3 (below).

SW1-1:  DTE Initiation of Local Analog Loopback Test

The setting for switch SW1-1 determines whether or not the Model

1035’s local analog loopback test can be initiated by raising pin 18 on
the DTE.

SW1-1

Setting

On

Pin 18 initiation enabled

Off

Pin 18 initiation disabled

SW1-2:  DTE Initiation of Remote Digital Loopback Test

The setting for switch SW1-2 determines whether or not the Model

1035’s remote digital test can be initiated by raising pin 21 on the DTE.

SW1-2

Setting

On

Pin 21 initiation enabled

Off

Pin 21 initiation disabled

SW1-3 through SW1-7:  Not Used

(continued)

5

SW1 SUMMARY TABLE

Position

Function

Factory Default

SW1-1

DTE Control of Analog Loopback 

On

Enabled

SW1-2

DTE Control of Digital Loopback 

On

Enabled

SW1-3

Not Used

Off

n/a

SW1-4

Not Used

Off

n/a

SW1-5

Not Used

Off

n/a

SW1-6

Not Used 

Off

n/a

SW1-7

Not Used

Off

n/a

SW1-8

V.54 Enable/Disable

Off

Enabled

Figure 3.  Summary of DIP switch settings for set SW1

SW1-8:  V.54 Enable/Disable

The setting for switch SW1-8 determines whether or not the Model

1035’s V.54 circuits are enabled.

SW1-8

Setting

On

V.54 test functions disabled

Off

V.54 test functions enabled

SWITCH  SET SW2

The configuration switches on switch set SW2 set data rate, clock

source, carrier control and RTS/CTS delay.  The default settings are
summarized in Figure 4.

SW2-1 through SW2-3:  Data Rate Setting

Switches SW2-1 through SW2-3 are set in combination to

determine the synchronous data rate for the Model 1035.

SW2-1

SW2-2

SW2-3

Setting

On

Off

Off

64 Kbps

Off

On

Off

56 Kbps

Off

Off

On

32 Kbps

(continued)

6

SW2 SUMMARY TABLE

Position

Function

Factory Default

SW2-1

Data Rate

Off

SW2-2

Data Rate

On

SW2-3

Data Rate

Off

SW2-4

Clock Source

On

SW2-5

Clock Source

On

SW2-6

Carrier Control

Off

Constantly On

SW2-7

RTS/CTS Delay

On

SW2-8

RTS/CTS Delay

On

Internal

56 Kbps

Figure 4.  Summary of DIP switch settings for set SW2

}

}

7 ms

}

Содержание RS-232










Отзывы: