background image

7. DTE Controlled Remote Digital Loop

Select Option 7 in the 

SOFTWARE CONFIGURATION Menu to

enable DTE control of the Remote Digital Loop Menu (See below).  The
Remote Digital Loop on the 1092ARC can be controlled from  the DTE
interface by selecting Enable (Option 1).  To instruct the 1092ARC to
ignore this request from the DTE interface, select Disable (Option 2).

8.  2-Wire/4-Wire Selection

Select Option 8 in the 

SOFTWARE CONFIGURATION Menu to

configure 2-Wire or 4-Wire operation. 

MAIN MENU Option 5:  Select Hardware/Software Control

Select Option 5 from the 

MAIN MENU selects  whether the Model

1092ARC will use the hardware switch settings or the software switch
settings for its active configuration.  If Options 1 or 2 are selected, the
1092ARC will use the current hardware or software switch settings as
the active configuration.  After changing this setting select MAIN MENU
Option 8 to implement the changes.

18

*******************************************************

*       

2-Wire/4-Wire Selection

*

*       

1. 4-Wire Mode   

*

*        

2. 2-Wire Mode

*

*

*

*******************************************************

4. DSR During Local Line Loop

Select Option 4 in the 

SOFTWARE CONFIGURATION 

to configure

the  behavior of the local Data Set Ready (DSR) signal during the Local
Line Loop test mode (below).

5. Response to Remote Digital Loop

Select Option 5 in the 

SOFTWARE CONFIGURATION 

Menu to

instruct the Model 1092ARC to either respond or ignore the Remote
Digital Loop request from the remote 1092ARC.

6. DTE Controlled Local Line Loop

Select Option 6 in the 

SOFTWARE CONFIGURATION Menu to

instruct the Model 1092ARC to either respond or ignore Local Line
Loop requests from the DTE. To instruct the Model 1092ARC to
respond to Local Line Loop requests from  the DTE, select Enable
(Option 1).  To instruct the 1092ARC to ignore Local Line Loop
requests from the DTE interface, select Disable (Option 2).

17

Содержание 1092ARC





















Отзывы: