-
if the accessories are damaged or in need of any repair, only the approved service centre is allowed for this
service. Alternatively, PATRON Bohemia a.s. customer department is available for products information.
-
only PATRON Bohemia a.s. replacement parts should be used on these accessories.
-
make sure you are familiar with the operation of the accessories.
-
all accessories can be washed by hands; alternatively the headrest fabric, siderests fabric, hiprests fabric,
abductor block fabric, fixation waistcoat, H - style harness, abductor belt, chest fixation belt can be
washed in washing machine (max. 40°)
-
never clean with ammonia based, bleach based or spirit type cleaners
-
after exposure to damp conditions leave in warm environment
-
store the accessories in a dry and safe place.
MAINTENANCE OF THE ACCESSORIES
10
In case of any repair on product needed or advise about particular functions, please contact below stated ap-
proved repair centre.
The repair centre is responsible as well for waste disposal of the device, accessory and packing.
Knee block
Loosen two hexagon-bolts placed on the rear side of footrest slider profile and take off the footplate. Put on the
knee block, set the position and fix the bolts into the assembly holes. Put on the footplate back into the right
position and properly tighten both hexagon-bolts.
Pelvis fixation
Unfasten the front narrower belts from the upholstery and put them through the aperture in the side plate and
upholstery of the seat. Attach the metal anchor by the nut which is fixing the position of the side plate. Unfas-
ten the back wider belts from the upholstery and put them through the aperture between the side plate and seat
base. Attach the metal anchor by the nut which is fixing the position of the side plate. Then fix the belts back to
the upholstery and tighten them according to the need.
Calf rest with fixation
Loosen two hexagon-bolts placed on the rear side of footrest slider profile and take off the footplate. Put on the
calf rest, set the position and fix the bolts into the assembly holes. Put on the footplate back into the right posi-
tion and properly tighten both hexagon-bolts.
Basket-HD (steel)
Screw the attachment adaptors for basket-HD to the back axle. Attach the basket to these adaptors by screws
with plastic rosace. Then attach the basket by belts with Velcro in front part of the stroller.
Tilt lock for spastic children
Unscrew backrest recline adjustment lever. Put tilt lock into the groove where the lever is moving and put the
second part of tilt lock onto the screw of the lever. Then screw on the lever back.
Grab bar brackets cover
Take off the grab bar and put on the plastic plug onto the grab bar bracket. Then put on the elastic cover and
fasten the rubber band onto the plastic nut placed on the bottom of the seat. Repeat the same procedure onto the
other side.
Basket - fabric
Clip the basket on the chassis frame tubes.
Maximum load
capacity is 3 kg.
Side trunkrest
(pair)
Seat the child into the stroller and find an appropriate height
of the trunkrest. (The trunkrests should be in the occupant’s
arm pits.) Take the child from the stroller. Find the relevant
fitting holes on the rear side of the backrest base and ( Re-
garding strollers Tom 4 Country and Tom 5 Streeter open
zippers ) according to requested location cut the holes as big
as metal plates of the side trunkrest through the fabric cover
or artificial leather. Put the metal plates of trunkrests through
the holes you cut in the upholstery. Put the screws through the
holes in the backrest base and secure them by nuts. You can
adjust the desired width of side trunkrests by the help of hori-
zontal slots in the metal plates of side trunkrests.
Headrest (pair) with neckrest
Before fitting the headrest with neckrest adaptor study the instruc-
tions from previous chapter. For fitting the neckrest adaptor in an
appropriate height use the dry zipper. Regarding strollers Tom 4
Xcountry and Tom 5 Streeter , open the head cushion first , attach
the neckrest using Velcro and then close the cushion.
3
Hip rest (pair)
Seat the child into the stroller and find the appropriate height of the
rests. Take the child out of the stroller. Stick the dry zipper under
the backrest upholstery in the relevant height. Attach the rests with
the dry zipper to the stroller.
Lumbar support (w.25cm, 35cm)
Cut through leatherine vertical straps or fabric ( Regard-
ing Tom 4 Xcountry and Tom 5 Streeter open zippers
first ) in backrest in previously determined height, and 5
cm in width. Run Velcro through holes in backrest
(w.5cm, l.30cm), which is sewed on the lumbar support.
Lift the backrest upholstery on the sides, and glue second
part of Velcro on the metal plate - 2pcs.
