4
1.
Main frame
2.
Seat support
3.
Foot plate
4.
Feet x 4
5.
Legs x 4
6.
Tras spacers x 2
7.
Tray frame
DESCRIPTION
Latest revision date: 08.01.2018
Dear customers
,
We thank you for your favour and purchasing of baby high chair BEE. Please read this manual carefully. If you, even with that, are not sure in using this
product, appeal to the seller with confidence.
SAFETY AND WARNING NOTES:
WARNINGS! Never leave the child in the chair without supervision
WARNINGS! Assure yourself the belts are correctly secured.
WARNINGS! Do not use the high chair when all parts are not set properly yet.
The supervising person must be familiarized with instructions noted in this manual
Do not use the high chair if some parts are missing or damaged.
Use safety belts every time when the child sits on the chair, the table does not serve for child’s safety.
Do not overburden the chair, it could be damaged and the child could be injured when it is has a heavier load.
Be careful not to danger yourself or the child when manipulating with the chair.
Do not use the chair for other purposes than it is constructed for.
The chair is designated for children from 6 month to 3 years (up to 20kg).
Company PATRON Bohemia a.s. does not bear the responsibility for the damages caused by using other accessories then supplied by this company.
Company PATRON Bohemia a.s. does not bear the responsibility for the damages and accidents caused by inappropriate use of the chair.
EN
INSTRUCTIONS FOR USE
Mounting
1. Take the seat support and thread it underneath the bar that goes across the back of the main frame Fig 1a. Do this until you
archive Fig 1b. Now do the same with the seat fabric until you achieve Fig 1c.
2. Slot the curved end of the seat support into the flap on the back of the seat fabric Fig 2a. Push the dnes of the tubes onto the
main frame tubes Fig 2b. now push fully down until the spring clips have come back through the holes Fig 2c.
3. Attach the foot plate to the main frame with four screws Fig 3.
4. Attach the feet to the corners of the legs with four screws Fig 4.
5. Place the tray spacers on to the plastic blocks of the tray frame. Fig5a. Place the lugs on the tray into the corresponding hles on
the tray frame and use the four remaining screws to secure Fig 5b.
6. Push the legs on the bortím of the tubes on the main frame and push together making sure the spring clips have come back
through the holes Fig. 6.
7. Open the framework, pull the legs apart Fig 7a. Continue to do thi until the cethes have locked into place Fig 7b.
8. Push the ends of the ray frame in to the plastic housing on the main frame Fig 8a. Push the tray downwards on to the bar in front
of the seat until it clicks in place and loop the straps around the bar and fasten the and to the press stud Fig 8b. Take the crutch
strap on the end of the seat unit, loop between both the bars under the tray and secure with press stud Fig 8c.
9. Your produkt should now look like this Fig 9.
Manipulation
To secure your child in the harness, push the buckle prones (A) + (B) into the buckle housing (C) until they snap into positron.
Adjust sliders to ensure a snug fit for your child. Repeat for the other side and also for the sholder straps Fig 10.
To fold the highchair, undo all the steps underneath the tray and flip the over the back of the seat unit. Now squeeze the catches on
the side.
MAINTENANCE
- the chair can be washed with warm water with addition of common detergent or disinfectant
never clean the chair with abrasive, ammonia or alcohol based cleaning compound, bleach and dissolvent
do not expose the chair to high temperature
Check and tighten the screw connections regularly.
If there are used control cables (brakes, telescopes, tilt), check it regularly and, if necessary, set up and oil them.
9
