Page
3
of 16 HPS 848 R.2
User section
O
O
R
R
I
I
G
G
I
I
N
N
A
A
L
L
R
R
E
E
M
M
O
O
T
T
E
E
C
C
O
O
N
N
T
T
R
R
O
O
L
L
O
O
P
P
E
E
R
R
A
A
T
T
I
I
N
N
G
G
PRESSING
THE
ORIGINAL
REMOTE
CONTROL
BUTTON
YOU
GET
THE
CLOSING
VEHICLE
AND
THE
ARMING
THE
SYSTEM:
CONFIRMED BY
:
•
1 beep (if enabled);
•
The LED on the dashboard turn ON;
•
Engine block ON (if connected);
•
Modules output arming (Windows lifter, ultrasonic, etc.);
The second press of the lock button allows disabling of ultrasound
sensors, wireless devices in Zone 2 and the rise of windows (if
connected). This function is subordinate to the vehicle type. If the
second pressure NOT run the exclusion perform the sequence "Lock -
Unlock - Block" of the original central locking with remote control in
quick succession. The exclusion is confirmed by 4 led blinks before
posting.
PRESSING
THE
OPENING
PUSHBUTTON
OF
THE
ORIGINAL
REMOTE
CONTROL
YOU
GET
THE
CONFIRMED
TO
DISARM
THE
ALARM:
•
2 beeps (if enabled);
•
Turning off the LED on the dashboard;
•
Deactivation of electric engine immobilization (if connected).;
•
Deactivation of modules output (windows lifter, ultrasonic, etc.);
After disarming, in the case of one or more alarm cycles, the LED will
remain fixe, indicating the presence of the alarm memory, that will be
displayed after opening the door. To stop it turn on the key.
PRESSING
THE
TRUNK
RELEASE
OF
ORIGINAL
REMOTE
CONTROL
If the device is armed the triggers for trunk opening, shock and
ultrasonic sensor will be inhibited to permit the access the trunk
compartment. The physical closure of the trunk will rearm the inhibited
triggers.
Attention: this function could be dependent on the type of vehicle used.
S
S
Y
Y
S
S
T
T
E
E
M
M
L
L
E
E
D
D
O
O
P
P
E
E
R
R
A
A
T
T
I
I
O
O
N
N
(
(
D
D
A
A
S
S
H
H
B
B
O
O
A
A
R
R
D
D
)
)
STATUS LED
INDICATION
−
OFF
System disarmed or power supplier missing
−
½ sec. ON - ½ sec. OFF
First power up or restart for power failure. Perform a locking and
unlocking cycle to turn it off.
−
ON fixed
Neutral time 10 sec. (after locking), or alarm memory ready for
showing (after unlocking). Open the driver's door and count the
LED flashes in a train of pulses. Check the sensor trigger the
"Alarm Memory" page.
−
1 flash every second
System armed and in surveillance.
−
3 sec. ON
–
1 sec. OFF
Vehicle selected not in memory, check the selection by PC,
eventually update the unit.
−
5 flash every second
An alarm is triggered. Alarm cycle lasts for 30 seconds.
−
2 flashes and pause
VALET function is active, system inhibited, this signaling occurs at
ignition key on and is repeated for a timeout (see VALET function).
−
3 flashes every second
IMMOBILIZER function is active (n°27), reset with pushbutton or
transponder.
−
Flashing very fast, 10
times per sec.
The device firmware is corrupted, tried to flash the firmware by PC
using a properly file.
