background image

7

X

s

 Preamp Owner’s Manual

 If  you have lost the jumpers, please contact either your dealer or 

the factory for replacements.  A single ended input without the XLR 

jumper will result in diminished performance.

You may now connect the power supply to it’s control chassis 

stages.  Other than being line voltage specific the power supplies are 

universal to the X

s

 Preamps.  Both right and left channel powerCON 

connections must be properly made up before AC power is applied.

powerCON cable end connectors insert into their respective 

chassis connectors and then lock with a 1/8 turn clockwise.  

Insert the cable connector into the chassis receptacle; turn to 

lock until they click and latch.   Verify that they latch and lock 

before proceeding.

Last cable to be attached is the mains cable.  Please make connection 

with the power supply IEC 320 socket first, house mains last.

Failure to follow this sequence can damage speakers and in some 

instances result in increased likelihood of  electrical shock.  As with 

all electrical devices the power cord (when used) is always the first to 

be removed and the last to be connected, no exceptions.

At this point you should be ready to play music.

The powersupply chassis connects to the electrical mains by a 

standard IEC 320 detachable power cord and to the control chassis 

by two 1.5 m powerCON umbilicals.  On the rear of  the power 

supply chassis is a single IEC 320 power inlet for connection to the 

mains, below a single 3AG fuse holder rated for AC mains duty.  To 

the left and right side two locking powerCON connectors, which will 

accept the supplied, interconnecting powerCON umbilicals.  

Safety disconnect is provided only by the detachable AC power 

cord.  Under normal operation access to the AC power cord must 

be maintained in the event of  electrical failure.  The AC power 

cord should be removed from the mains and then the power supply 

when the unit is left unused or during atmospheric electrical events 

(lightening storms).  Under normal circumstances and for best sonic 

performance the unit is left powered up continuously.

The control chassis is a true dual mono design: Right and left 

channels receive power independently via independent dedicated 

powerCON umbilical cables.  In all instances of  power and signal 

Physical Description 

and Operation

Содержание Xs Preamp















Отзывы: